Contact Us

AD8220ARMZ

Brand: Analog Devices
Analog Devices AD8220ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8220ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8220ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8220ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8220ARMZ: JFET Input Instrumentation Amplifier in an MSOP

The AD8220ARMZ is a JFET input instrumentation amplifier with a maximum input bias current of 10 pA and a maximum input offset current of 0.6 pA in the B grade, which is the reason it exists: a bipolar input amplifier with nanoamp bias currents cannot measure a high impedance source without an offset that moves with temperature. Bandwidth is 1.5 MHz at unity gain, input noise is 14 nV per root hertz at 1 kHz, slew rate is 2 V per microsecond, and quiescent current is 750 microamps maximum. Gain is set with one resistor from 1 to 1000, the output is rail to rail, the input range extends below the negative rail, and the supply is 4.5 V to 36 V single or plus and minus 2.25 V to 18 V dual.

Published values

ParameterValue
Input bias current10 pA maximum, B grade
Input offset current0.6 pA maximum, B grade
Gain1 to 1000, set by one resistor, G = 1 + 49.4 kohm divided by RG
Common-mode rejection100 dB minimum at gain of 10, 80 dB minimum to 5 kHz at gain of 1
Bandwidth1.5 MHz at unity gain
Input noise14 nV per root hertz at 1 kHz
Slew rate2 V per microsecond
Quiescent current750 microamps maximum
Supply4.5 V to 36 V single, plus and minus 2.25 V to 18 V dual
Input rangeExtends below the negative rail, output rail to rail
ESD4 kV
Package8-lead MSOP

Ten picoamps is what buys a photodiode or a pH electrode

A 10 pA bias current through a 1 Gohm source impedance is 10 mV of offset. A bipolar input part with 1 nA of bias current through the same source is 1 V, which saturates the amplifier. That ratio is the whole argument for a JFET input, and it is why the part appears in photodiode front ends, pH and ion sensors, and high impedance bridge circuits. The catch is that the picoamp bias current doubles roughly every 10 degrees Celsius, so a 10 pA maximum at 25 degrees is around 300 pA at 85 degrees. Measure the source impedance at the maximum operating temperature, not at room temperature, before assuming the part is suitable.

The gain resistor and the noise it brings

Gain is 1 plus 49.4 kohm divided by RG, so a gain of 100 needs about 499 ohm. That resistor, plus the 49.4 kohm internal resistors, form the noise gain, and at a gain of 100 the input referred noise from the resistor network is dominated by the 49.4 kohm divided by the gain, which is about 494 ohm, or 2.8 nV per root hertz at room temperature. Add the 14 nV of the amplifier itself and the total is around 14.3 nV, so at moderate gains the amplifier sets the noise. At a gain of 1000 the resistors contribute about 0.9 nV and the amplifier still dominates, which is a comfortable place to be: this family is not resistor-noise limited at any gain it is used at.

Input below the negative rail, in practice

The input range extends below the negative supply, which matters for a single supply bridge measurement where the signal sits at ground. The limit is a few hundred millivolts below the rail depending on gain, and the output swing to the rails is what allows a 5 V single supply part to read a signal centred at 2.5 V without a mid-rail reference. Check the common-mode range curve for the gain in use: the range narrows as gain rises, and a circuit that works at a gain of 10 can clip at a gain of 500 with the same input. The reference pin sets the output offset and should be driven from a low impedance, since it is a direct input to the output stage.

Availability and second sourcing

A JFET input instrumentation amplifier cannot be replaced by a bipolar one without checking the source impedance and the temperature range, and the pinout is only half the story: the gain equation and the common-mode range also have to match. The amplifier cross reference page groups the instrumentation amplifiers by input type and gain range, the ADI part second source page lists the grades that match on bias current, and the medical device components page covers the applications where this input current is a regulatory rather than an engineering choice.