Contact Us

AD8184ARZ

Brand: Analog Devices
Analog Devices AD8184ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8184ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8184ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8184ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8184ARZ: 4-to-1 Video Multiplexer at 700 MHz and 4.4 mA

The AD8184ARZ is a four input, one output video multiplexer with fully buffered inputs and output, 700 MHz of minus 3 dB bandwidth, a 750 V per microsecond slew rate and 10 ns channel switching. It draws 4.4 mA from plus and minus 5 V. The analog specifications are the ones that matter in a video path: 0.1 dB gain flatness to 75 MHz, 0.01 percent differential gain error and 0.01 degree differential phase error into a 10 kohm load, crosstalk of minus 95 dB at 5 MHz between channels, and off isolation of 115 dB at 5 MHz. It is pin compatible with the HA4314 and GX4314 multiplexers, which is the reason it still appears in long lived broadcast and display boards.

Published values

ParameterValue
Configuration4 to 1, buffered inputs and output
Bandwidth700 MHz, minus 3 dB
Slew rate750 V per microsecond
Channel switching10 ns
Settling15 ns to 0.1 percent
Gain flatness0.1 dB to 75 MHz
Differential gain and phase0.01 percent and 0.01 degree into 10 kohm
Crosstalkminus 95 dB at 5 MHz
Off isolation115 dB at 5 MHz
Supply current4.4 mA
SupplyPlus and minus 5 V
Package14-lead PDIP and SOIC

The output is not a perfect buffer

The gain is approximately 0.97 V per volt into a 1 kohm load, which is a 3 percent loss, and it approaches unity as the load lightens. Into 10 kohm the differential gain and phase numbers hold; into 75 ohm, which is the video standard, the gain drops further and the distortion rises. This is the trap when the part is moved from a display board with a high impedance input to a cable driver: the multiplexer is a switch, not a line driver, and it needs a separate cable driver stage after it, or a 75 ohm back-terminated arrangement with the level made up elsewhere. Read the load column of the specification table before assuming the 700 MHz figure applies to a terminated cable.

The disable pin is what makes cascading possible

The output can be put into a high impedance state, so several multiplexers can share one bus. In the disabled state the output capacitance is what loads the bus, and the 115 dB of off isolation is measured at 5 MHz with that capacitance in place. Cascade three devices and the bus sees three times the capacitance plus the trace, which moves the bus pole down by roughly a factor of three. On a 700 MHz part that is still several hundred megahertz, but it is no longer the number in the headline. Keep the shared bus as short as the board allows, and put the terminator at the far end rather than at each device.

Switching transients and the 25 mV glitch

Channel switching produces a glitch of less than 25 mV at the output, which in a video signal is a fraction of a percent of the 1 V composite level. In a picture-in-picture switcher that is invisible. In a pixel switching application at 10 ns per channel it matters, because the glitch lands inside the active line. The mitigation is to switch during blanking, which is what the 10 ns switching time is there to allow, and to keep the input source impedance low so the buffered input recovers quickly. Both inputs of the unused channels should be terminated rather than left floating, because a floating input couples the switching transient into the selected channel through the package.

Availability and second sourcing

The pin compatibility with the HA4314 and GX4314 is the practical route when the original is short: the footprint and the control logic are shared, and the differences are in bandwidth and in the load specification, so the surrounding circuit usually survives. The amplifier cross reference page lists the analog switches and multiplexers by function, the pin to pin cross reference page covers the 14-lead footprints, and the verification checklist is the sequence to run on a substitute before a board is released.