Contact Us

AD8139ARDZ

Brand: Analog Devices
Analog Devices AD8139ARDZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8139ARDZ — Analog & Mixed-Signal ICs | Superb Automation

AD8139ARDZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8139ARDZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8139ARDZ: 2.25 nV Noise Differential Driver for 18-Bit Converters

The AD8139ARDZ is a fully differential amplifier built for one job: driving a high resolution converter without adding noise that the converter can see. Input voltage noise is 2.25 nV per root hertz and current noise is 2.1 pA per root hertz, spurious free dynamic range is 98 dBc at 1 MHz, 85 dBc at 5 MHz and 72 dBc at 20 MHz, and the part settles to 0.01 percent in 45 ns. Bandwidth is 410 MHz at unity gain, slew rate is 800 V per microsecond, and the supply range is 5 V to 12 V, which is what allows a 4 V peak to peak differential signal to be delivered to a converter running on a 5 V reference. Output balance is 69 dB at 1 MHz and DC common-mode rejection is 80 dB.

Published values

ParameterValue
Input voltage noise2.25 nV per root hertz
Input current noise2.1 pA per root hertz
Distortion98 dBc at 1 MHz, 85 dBc at 5 MHz, 72 dBc at 20 MHz
Bandwidth410 MHz at gain of one
Slew rate800 V per microsecond
Settling45 ns to 0.01 percent
Input offset voltage0.5 mV maximum
Input offset current0.5 microamp maximum
Output balance69 dB at 1 MHz
Supply range5 V to 12 V
OutputRail to rail
Package8-lead SOIC with exposed paddle, 3 mm by 3 mm LFCSP

Why 2.25 nV matters at 18 bits

An 18-bit converter on a 5 V reference has a code size of 19 microvolts. Spread over a 1 MHz bandwidth, 2.25 nV per root hertz integrates to 2.25 microvolts RMS, which is a tenth of a code, so the amplifier noise is not the limit. Run the same amplifier into a 20 MHz bandwidth and the noise becomes 10 microvolts RMS, half a code, and the last two bits are gone. That is the honest trade: the part is quiet enough for 18 bits only when the bandwidth in front of the converter is limited, which is why the datasheet numbers are given at 1, 5 and 20 MHz rather than as a single figure. The current noise sets the resistor ceiling: at 2.1 pA per root hertz, a 1 kohm feedback network contributes 2.1 nV per root hertz of its own, so doubling the resistors doubles the total noise. Below 1 kohm the voltage noise dominates, above it the resistor noise does.

Five to twelve volts is not a convenience

The supply range is the reason this part exists in the precision segment. A converter with a 5 V reference needs a 5 V peak to peak differential input, which is 2.5 V peak on each output around a 2.5 V common mode. A rail-to-rail output amplifier on a single 5 V rail cannot deliver that with any linearity. The AD8139 runs on up to 12 V, so the outputs sit at 2.5 V plus or minus 1.25 V with 2.5 V of headroom at each rail, and the distortion numbers hold. The price is a second supply rail and the sequencing that comes with it: the amplifier must not drive the converter input before the converter supply is up, or the input protection diodes conduct. A series resistor of 10 ohm to 25 ohm at each output limits that current and also isolates the converter's sampling glitch from the amplifier output.

The exposed paddle and the LFCSP need different copper

The 8-lead SOIC has an exposed paddle on the underside that must be soldered to a copper area connected to the negative supply or to ground, depending on the rail arrangement, because it is the thermal and electrical reference for the die. The 3 mm by 3 mm LFCSP has the same paddle but far less copper to spread into, so the thermal path depends on the vias under the part. Both packages are rated to 125 degrees junction, and the dissipation is modest, but a paddle left floating on either package shows up as degraded distortion at high frequency rather than as a failure. Treat the paddle as a required connection on both footprints and keep the feedback traces short and symmetric.

Availability and second sourcing

A low noise differential driver cannot be replaced by a generic one: the noise, the distortion at 20 MHz and the 12 V supply range all have to be met together, and a substitute that misses any of them changes the effective resolution of the converter behind it. The amplifier cross reference page sorts the differential drivers by noise and supply, the ADI part second source page lists the grades that match on all three, and the pin to pin cross reference page covers the 8-lead footprints.