Contact Us

AD8132ARZ

Brand: Analog Devices
Analog Devices AD8132ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8132ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8132ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8132ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8132ARZ: 350 MHz Differential Amplifier with Resistor Set Gain

The AD8132ARZ is the flexible member of the low cost differential amplifier pair: 350 MHz at minus 3 dB, 1200 V per microsecond, gain set by four external resistors, and output balance of minus 68 dB at 10 MHz from the same internal common-mode feedback that the fixed gain AD8131 uses. Quiescent current is 10.7 mA on a 5 V rail, the supply range is 2.7 V to 5.5 V, and distortion is minus 99 dBc spurious free dynamic range at 5 MHz into an 800 ohm load. The automotive version, AD8132W, is qualified to AEC-Q100, which is the reason this part turns up in camera links and sensor interfaces rather than only in bench instruments.

Published values

ParameterValue
Bandwidth350 MHz, minus 3 dB
Slew rate1200 V per microsecond
GainSet by external resistors, differential or single ended input
Output balanceminus 68 dB at 10 MHz
Distortionminus 99 dBc SFDR at 5 MHz into 800 ohm
Supply current10.7 mA at 5 V
Supply range2.7 V to 5.5 V
Common-mode controlVOCM pin
Input offset voltage1 mV typical
AutomotiveAD8132W, AEC-Q100 qualified
Package8-lead SOIC and 8-lead MSOP

Four resistors decide the gain and the input impedance

With external feedback the input impedance is a choice rather than a constant. Set the four resistors for a gain of two and a 1 kohm differential input, and the driving stage sees 1 kohm. Set them for the same gain with 5 kohm resistors and it sees 5 kohm but with four times the thermal noise and four times the sensitivity to the feedback node capacitance. The practical rule is to keep the feedback resistors low enough that the pole they form with the amplifier input capacitance stays well above the signal band, and high enough that the previous stage can drive them. For a 10 MHz signal, a few hundred ohms to 2 kohm is the usual window, and the resistor tolerance directly becomes gain and balance error because the internal loop only corrects the common mode.

Boosting the high end with the feedback network

Because the network is external, a capacitor across the feedback resistor turns the pair into a differential equaliser for a twisted pair or a coaxial cable whose loss rises with frequency. The same capacitor sets the bandwidth limit, so the value is chosen from the cable length and the required flatness rather than from the amplifier alone. The reason this matters in a camera or sensor link is that a passive cable equaliser costs more board area than two capacitors, and the differential amplifier is already in the signal path. Keep the two halves symmetric: a mismatch of a few percent in the capacitors shows up as common-mode to differential conversion at high frequency, which is exactly what the minus 68 dB balance figure is protecting.

Power and thermal in a small package

10.7 mA on 5 V is 54 mW in the amplifier plus whatever the load draws. In the 8-lead MSOP with no thermal pad, the junction rises by roughly 190 degrees per watt, so 54 mW is about 10 degrees, which is comfortable. Drive a 100 ohm differential cable at 2 V peak to peak and the output stage adds 20 mW, still fine. The number to watch is the short circuit current into a miswired cable: the part survives it, but the supply rail will sag and the ADC behind it will see the sag as a common-mode step. A series resistor of 10 ohm to 25 ohm at each output is the cheap protection and it also isolates the cable capacitance.

Availability and second sourcing

The resistor set gain is what makes substitution risky: a drop-in part with a different internal architecture will not have the same gain for the same four resistors, and the filter around it was tuned to the present one. The amplifier cross reference page groups the differential drivers by function and supply, the ADI part second source page lists the grades that are genuinely equivalent rather than merely similar, and the lead time page shows the current availability position.