Contact Us

AD8131ARMZ

Brand: Analog Devices
Analog Devices AD8131ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8131ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8131ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8131ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8131ARMZ: A Fixed Gain of Two Differential Driver in MSOP

The AD8131ARMZ is a differential or single ended to differential output driver with a fixed gain of two and no external gain components, in an 8-lead MSOP. Full power bandwidth is 400 MHz at 2 V peak to peak differential, slew rate is 2,000 V per microsecond, and spurious free dynamic range is 68 dB at 5 MHz into a 200 ohm differential load. Internal feedback sets the gain and balances the two outputs to minus 60 dB at 10 MHz, which is the figure that keeps common mode energy off a twisted pair. The common mode output level is set by a voltage on the VOCM pin, so a dual supply signal can drive a single supply converter without a transformer. The part runs from plus 2.7 V to plus and minus 5 V and is specified from minus 40 to plus 125 degrees Celsius.

Published values

ParameterValue
FunctionSingle ended or differential input to differential output driver
GainFixed at 2, no external gain components
Full power bandwidth400 MHz at 2 V peak to peak differential
Slew rate2,000 V per microsecond
Output balanceMinus 60 dB at 10 MHz
Distortion68 dB spurious free at 5 MHz into 200 ohm
Common mode controlVOCM pin sets the output common mode
Input networkInternal 750 ohm and 1.5 kohm resistors
SupplyPlus 2.7 V to plus and minus 5 V
Body8-lead MSOP and 8-lead SOIC
Temperature rangeMinus 40 to plus 125 degrees Celsius

A fixed gain of two is a constraint on the source

Because the gain is fixed, the input signal has to be scaled before it reaches this part. Driving a 2 V peak to peak differential output needs a 1 V peak to peak input, and an input larger than that clips the output no matter what the supply is. In a converter driver this is usually the right arrangement, since the converter's full scale is known and the upstream stage can be scaled once. In a general purpose line driver it means a resistive attenuator ahead of the part, and the attenuator's tolerance adds directly to the gain error because the internal resistors are trimmed and the external ones are not.

The internal resistor network and the load it presents

The two 750 ohm input resistors put a 1.5 kohm differential load on the source, and the 1.5 kohm resistors to the VOCM node set the common mode feedback. A source with a significant output impedance therefore loses gain before the driver sees the signal, and a source that is single ended sees one of those resistors to ground, so the effective input impedance differs between single ended and differential drive. That difference is the most common reason a board that works with a differential source measures low with a single ended one, and it is worth computing before choosing the upstream stage.

Two thousand volts per microsecond at 400 MHz

The slew rate supports 796 mV peak at 400 MHz, so the full power figure of 400 MHz and the slew rate are consistent for a 2 V peak to peak differential output, which is 1 V peak on each output. That is a genuinely wideband driver, and it is why the part is used to replace a transformer in a video or a data line: it preserves the low frequency and direct current content that a transformer cannot pass, and it does not have the magnetic susceptibility or the hysteresis of a wound component.

VOCM and level shifting into a single supply converter

The VOCM pin sets the output common mode independently of the differential signal, so a signal that swings around zero on plus and minus 5 V can be moved to a 1.25 V common mode for a single supply converter without changing the differential amplitude. The accuracy of that common mode depends on the voltage applied and the gain from VOCM to the outputs, which is nominally one, and any noise on the VOCM node appears as common mode on the pair and is rejected by the converter's differential input to the extent of its common mode rejection. A noisy reference on this pin is therefore less harmful than it looks, but a DC error is not rejected at all.

MSOP body and the balance specification

The 8-lead MSOP is the smaller of the two bodies and has a higher thermal resistance, which matters because the part drives a terminated pair and the output current is not small. The minus 60 dB balance at 10 MHz is the number that describes how much of the differential signal leaks into the common mode, and it depends on the internal resistor matching rather than on the board, so a substitute part with a looser balance specification will radiate more even if its bandwidth is higher. On a long cable that difference shows up as emissions and as a bit error rate that rises with cable length. The amplifier cross reference page groups the differential driver parts by bandwidth and gain, the ADI part second source page covers the grades that are genuinely equivalent, and the how to verify a drop in replacement page lists the checks for a driver substitution.