AD7610BSTZ
Product Specifications
AD7610BSTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7610BSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7610BSTZ: 16 Bits at 250 kSPS From One 5 V Rail With Four Programmable Ranges
The AD7610 is a 16-bit successive approximation converter with a throughput of 250 kSPS, programmable input ranges of plus and minus 5 V, plus and minus 10 V, 0 V to 5 V and 0 V to 10 V selected by pin or by software, and an integral nonlinearity of 0.75 LSB typical and 1.5 LSB maximum, which is 23 ppm of the full scale range. Signal to noise ratio is 94 dB at 2 kHz, the internal reference is 5 V with a typical drift of 3 ppm per degree C, and the die carries a temperature sensor. It has no pipeline delay, offers a parallel 16-bit or 8-bit bus and a serial port that works at 5 V or 3.3 V, dissipates 90 mW at 250 kSPS and 10 mW at 1 kSPS, and comes in a 48-lead LQFP or LFCSP.
1.5 LSB on a 20 V span is 458 uV, and 94 dB is 15.3 effective bits
On the plus and minus 10 V range the span is 20 V, so one code is 305 uV and 1.5 LSB of maximum nonlinearity is 458 uV. Signal to noise ratio of 94 dB corresponds to (94 minus 1.76) divided by 6.02, which is 15.3 effective bits, so the 16-bit word is filled to within 0.7 bits and the limit is set by the input network and the reference rather than by the converter core. That is a strong pair of numbers for a 250 kSPS part, and it is why this converter is used where a moderate rate and a wide input range matter more than raw speed.
90 mW at full rate and 10 mW at 1 kSPS
The power figure scales with the rate because the converter powers down between conversions, so a board that reads a slow process variable a few times a second spends almost nothing. The ratio is nine to one between 250 kSPS and 1 kSPS, which is what allows the same part to serve a fast scanner and a slow monitor. In a battery instrument that reads at 1 kSPS the converter is not the load, the host is, and the 10 mW figure is what makes the choice possible without a separate low power converter for the standby mode.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 16 bits, no missing codes | 305 uV per code on a 20 V span |
| Throughput | 250 kSPS | 4 us per conversion, acquisition included |
| Input ranges | Plus and minus 5 V, 10 V, 0 V to 5 V, 10 V | Pin or software selected |
| Integral nonlinearity | 0.75 LSB typical, 1.5 LSB maximum | 23 ppm of full scale, 458 uV on 20 V |
| Signal to noise ratio | 94 dB at 2 kHz | 15.3 effective bits |
| Reference | 5 V internal, 3 ppm per degree C typical | 300 ppm over 100 degrees, 49 codes on 20 V |
| Temperature sensor | On chip | Board temperature without a separate part |
| Pipeline delay | None, successive approximation | The result belongs to the conversion just issued |
| Interfaces | Parallel 16 or 8 bit, serial 5 V or 3.3 V | Host choice without a level shifter |
| Power | 90 mW at 250 kSPS, 10 mW at 1 kSPS | Scales with rate, so standby is cheap |
| Supply | 5 V analog, separate digital supply | Separate logic rail for a 3.3 V host |
| Package | 48-lead LQFP or LFCSP | LFCSP for the smaller board |
| Architecture | Charge redistribution with on chip calibration | Linearity that does not need a factory trim |
No pipeline delay changes what the host can do
A pipelined converter returns the result of a conversion started several clock cycles earlier, so the host has to track which sample it is reading and any change in the input during the pipeline latency is lost or aliased. A successive approximation converter with no pipeline delay returns the sample that was just taken, so a control loop can act on it immediately and a multiplexed channel list does not need a matching delay line in software. At 250 kSPS the difference is 4 us per sample, and in a four channel multiplexed system that is the whole loop's timing budget.
The reference drift is the accuracy limit, not the linearity
The internal reference drifts 3 ppm per degree C typical, which over 100 degrees is 300 ppm, or 3 mV on a 10 V range. One code is 305 uV, so the drift is about 49 codes, thirty times the maximum nonlinearity. A channel calibrated at 25 degrees C and used at 70 degrees C therefore moves by the reference drift, and the fix is either an external reference with better drift or a ratiometric arrangement where the same reference drives the source. This is the same conclusion as with any 16-bit converter: the reference and the input network decide the absolute accuracy, and the converter's own linearity is the smaller term.
Driving the input on a 250 kSPS part
The switched capacitor input presents a transient to the driving amplifier at the start of each acquisition, and at 250 kSPS the acquisition window is short. The amplifier has to settle that transient to better than half a code in the time available, which for a 16-bit part at 20 V span is 150 uV. A slow precision amplifier with a 1 MHz bandwidth will not do it, and the resulting error appears as a code dependent offset that changes with the source impedance. The data sheet specifies the acquisition time and the recommended amplifier, and the amplifier's settling time to 0.001 percent is the parameter to compare against that window.
Sourcing a 250 kSPS 16-bit converter
The order code fixes the package, and the LQFP and LFCSP versions differ in thermal path and board area rather than in function. Converters that can be compared on rate, range and interface are listed in ADC DAC cross reference, the industrial instrument side of a bill of materials is covered in OEM procurement, and where the exact code is short the options are set out in component lead time solutions.