AD629BRZ
Product Specifications
AD629BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD629BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD629BRZ: The Grade Where 3 ppm of Gain Nonlinearity Is the Specification
The AD629BRZ is the B grade of the 270 V common mode difference amplifier, and the two numbers that separate it from the A grade are 3 ppm maximum gain nonlinearity and 86 dB minimum common mode rejection at 500 Hz. At a gain of one there is no external resistor network to trim, so those two figures plus the offset window are the entire error budget, and a B grade part is chosen when the measurement is a small difference sitting on a large common mode. Supply current stays at 1 mA maximum and the bandwidth stays at 500 kHz, so the grade buys accuracy and nothing else. The body is the 8-lead surface mount outline shared with the A grade.
Published values
| Parameter | Value |
|---|---|
| Nominal gain | 1 V per volt, fixed |
| Gain nonlinearity, B grade | 3 ppm maximum |
| Common mode rejection, B grade | 86 dB minimum at 500 Hz |
| Common mode range | Beyond 270 V with plus and minus 15 V supplies |
| Supply current | 1 mA maximum |
| Bandwidth | 500 kHz |
| Input protection | Common mode and differential overvoltage |
| Body | 8-lead surface mount, R suffix |
| Die form | Listed separately in the ordering guide |
Reading 3 ppm against a 12 bit converter
One least significant bit of a 12 bit converter on a 5 V range is 1.2 mV, which is 244 ppm of full scale, so 3 ppm of gain nonlinearity is 80 times smaller than a bit and invisible in the conversion. The figure starts to matter when the measurement is averaged or when the converter behind the amplifier is 16 bit or better: at 16 bit a bit is 15 ppm, and 3 ppm of nonlinearity becomes a fifth of a bit. That is the point at which the grade choice shows up in the noise floor of the result rather than in the specification table, and it is why instrumentation with a 24 bit converter asks for the B grade as a matter of course.
Common mode rejection at 500 Hz, not at dc
A cell monitor on a stack that switches at a few kilohertz sees its common mode move at the switching frequency, not at dc. The published rejection is specified at 500 Hz precisely because that is where the interference lives, and a part specified only at dc can look excellent on paper and poor in the rack. The 86 dB figure at 500 Hz means a 100 V common mode step maps to about 5 mV of apparent differential signal, which is still large against a cell voltage, so the rejection has to be supported by a filter at the amplifier output rather than by the amplifier alone.
Which grade to hold, and when the die makes sense
Programs that build the same board in volume for a decade sometimes move to the die form, and the ordering guide lists it as a separate line with its own temperature grade. The die route changes the incoming inspection requirement, because a bare die cannot be tested on a board the way a packaged part can, and it moves the qualification onto the assembly house. Where the volume does not justify that, the packaged B grade is the simpler answer. The amplifier cross reference lists the difference amplifier families we supply, the incoming inspection plan covers how a batch is checked against the grade it claims, and the lead time page shows what is on the shelf now.