Contact Us

AD627ARZ

Brand: Analog Devices
Analog Devices AD627ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD627ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD627ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD627ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD627ARZ: 85 Microamps of Supply Current and a Minimum Gain of Five

The AD627ARZ is a micropower instrumentation amplifier with rail to rail output, and its two headline numbers are 85 microamps maximum supply current and a gain range that starts at 5 rather than 1. The gain equation is G equals 5 plus 200 k divided by RG, so the part cannot be used at unity gain, which is a deliberate consequence of the two op amp topology used to reach that supply current. Gain accuracy is 0.03 percent typical at a gain of 5 for the A grade, input offset is 200 microvolts maximum on dual supplies for the A grade and 125 microvolts for the B grade, input bias current is 10 nA maximum, and input referred noise is 38 nV per root hertz at a gain of 100. Common mode rejection at a gain of 5 is 77 dB minimum for A and 83 dB for B, bandwidth at that gain is 80 kHz, and settling to 0.01 percent for a 5 V step is 135 microseconds.

Published values

ParameterValue
Gain equationG equals 5 plus 200 k divided by RG
Gain range5 with no resistor to 1000
Supply current85 microamps maximum
Supply range2.2 V to 36 V, single or dual
Input offset, A grade dual supply200 microvolts maximum
Input offset, B grade dual supply125 microvolts maximum
Gain accuracy at G equals 50.03 percent typical, A grade
Input bias current10 nA maximum
Input noise38 nV per root hertz at 1 kHz, G equals 100
Common mode rejection at G equals 577 dB minimum A, 83 dB minimum B
Bandwidth at G equals 580 kHz
Settling to 0.01 percent135 microseconds, 5 V step at G equals 5

Why the minimum gain is five, and when that hurts

Two op amp in-amps reach low supply current by sharing one output stage between the input pair and the difference stage, and the topology fixes a minimum gain of 5. Any program that needs a buffer or a gain of 2 has to add a divider in front of the part, and the divider has to be low enough in impedance to keep the bias current error small, which then loads the sensor. Where the signal is a bridge output of a few millivolts the minimum gain is irrelevant and even helpful, because the gain of 5 is the first stage of the chain rather than the whole thing. Where the requirement is a unity gain difference amplifier, the AD623 or the AD628 is the right part and this one is not.

A 2.2 V supply floor and the loop powered case

The supply range starts at 2.2 V, which is low enough to run from two alkaline cells or from a shunt regulator in a 4 to 20 mA loop. In a loop powered transmitter the whole circuit has to fit inside the 4 mA budget, and 85 microamps for the amplifier leaves room for a reference and a converter. The rail to rail output matters here too, because the available headroom is small when the loop current is at the bottom of its range and the sense resistor is dropping only a couple of volts.

Choosing a grade and a body

The A and B grades differ in offset and in common mode rejection rather than in supply current, so a channel that only needs the micropower behaviour can take the A grade and put the difference into calibration. The body is the same 8-lead outline in both grades, and the pinout matches the rest of the family, so grade changes are a line item change. Where the exact grade has gone short, the substitution question is whether the drift budget can absorb the offset window, and that is answered from the data sheet rather than from a distributor listing. The amplifier cross reference lists the micropower families we supply, the lead time page shows what is on the shelf, and the obsolete part cross reference hub covers the case where a grade has been discontinued.