Contact Us

AD5754RBREZ

Brand: Analog Devices
Analog Devices AD5754RBREZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD5754RBREZ — Analog & Mixed-Signal ICs | Superb Automation

AD5754RBREZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD5754RBREZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD5754RBREZ: The Same Four Bipolar Channels With a 2.5 V Reference Already Inside

The AD5754R is the version of the quad 16-bit voltage output converter that carries its own 2.5 V reference, specified at 5 ppm per degree C maximum, together with the reference buffers for all four channels. Everything else is the same as the external reference member of the family: 4.5 V to 16.5 V single or dual supplies, software selectable spans of plus and minus 5 V, 10 V and 10.8 V and the three unipolar equivalents, 16 LSB maximum integral nonlinearity, 0.1 percent total unadjusted error, 10 us typical settling, simultaneous update from LDAC, asynchronous clear to zero or midscale, and a 30 MHz SPI port in a 24-lead TSSOP over minus 40 to plus 85 degrees C.

625 ppm of reference drift is 41 codes on the wide span

The internal reference is specified at 5 ppm per degree C maximum, so over the 125 degree ambient range of the part the reference moves 625 ppm. On the plus and minus 10.8 V span, which is 21.6 V, 625 ppm is 13.5 mV, and one code on that span is 330 uV, so the reference drift alone is 41 codes. That is more than twice the 16 LSB integral nonlinearity, which means the on chip reference drift, not the converter linearity, is what limits absolute accuracy over temperature once the channel has been trimmed at room temperature. The number is not a defect: a 5 ppm reference in a 24-lead TSSOP is a good reference, and the arithmetic is what tells an engineer whether the internal reference is enough or an external ovenized or buried zener reference is needed.

What the integrated reference saves and what it costs

An external precision reference plus four buffers is three to five components, a board area that keeps the reference away from the digital lines, and a placement decision on every board revision. Integrating it removes all of that and shrinks the bill of materials. The cost is thermal: the reference sits on the same die as four output amplifiers, and the die temperature moves with the load current, so the reference sees a thermal excursion that a separate reference part would not. Where the outputs drive small loads the effect is small, and where they drive 10 mA into a low impedance the reference drift tracks the load pattern.

ParameterValueWhat it decides
Resolution16 bits, four channelsOne code is 330 uV on the plus and minus 10.8 V span
Internal reference2.5 V, 5 ppm per degree C maximum625 ppm over 125 degrees, 41 codes on the wide span
Reference buffersIntegrated, one per groupNo external buffer to place or route
Integral nonlinearity16 LSB maximum5.28 mV on the wide span, smaller than the drift
Total unadjusted error0.1 percent of full scale21.6 mV on the wide span, before trimming
Output rangesPlus and minus 5 V, 10 V, 10.8 V, and three unipolarRegister selected, no component change
Settling time10 us typicalAbout 100 kHz of useful update rate
SuppliesSingle or dual 4.5 V to 16.5 VPlus and minus 15 V gives 4.2 V of headroom
Simultaneous updateLDAC pulseAll four channels on one edge
Asynchronous clearZero scale or midscaleFail safe state without the serial port
InterfaceSPI to 30 MHzDouble buffered, load then update
Package24-lead TSSOPSame footprint as the external reference part
Temperature rangeMinus 40 to plus 85 degrees CThe industrial band, not the automotive one

Same footprint, different bill of materials

The R and non R parts share a footprint, and that is a deliberate platform decision: a board can be built with the internal reference version and, if a customer needs better drift, the same board takes the external reference version with the reference fitted and the internal one disabled. The register settings for the output range are the same, so the firmware does not change. That makes the choice between them a procurement decision as much as an electrical one, and it is why both members stay in a bill of materials long after a product has been released.

The plus and minus 10.8 V range and its supply headroom

A 10.8 V output from a 15 V rail leaves 4.2 V across the output device at zero current, and the amplifier drops that as load current rises. At 10 mA the device dissipates 42 mW, times four channels is 168 mW in a 24-lead TSSOP, which is manageable without a heat sink but is not free. Dropping the rails to plus and minus 12 V halves the dissipation and leaves 1.2 V of headroom, which is enough for a light load and not enough for a heavy one. The supply choice is therefore a load current decision, and the data sheet output swing figures are specified with the load stated for exactly this reason.

Sourcing the quad source with the internal reference

The order code distinguishes the internal reference part from the external reference part and both are in production, so a substitution in either direction has to be made on the board and not just in the stores system. The converters that can be compared on channel count, span and reference are listed in ADC DAC cross reference, the incoming check that catches a wrong reference variant is described in incoming inspection plan, and the supplier side of a mixed converter bill of materials is covered in one stop BOM sourcing.