Contact Us

AD5272BRMZ-50-RL7

Brand: Analog Devices
Analog Devices AD5272BRMZ-50-RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD5272BRMZ-50-RL7 — Analog & Mixed-Signal ICs | Superb Automation

AD5272BRMZ-50-RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD5272BRMZ-50-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD5272BRMZ-50-RL7: a 1024 position, 50 kohm digital rheostat

The AD5272BRMZ-50-RL7 is the 50 kohm, 1024 position single channel digital rheostat of the AD5272/AD5274 family in the 10 lead MSOP. It holds plus or minus 1 percent end to end resistor tolerance, 5 ppm per degree C of rheostat mode temperature coefficient, an I2C compatible interface with wiper readback, and 50 times programmable memory that reloads the wiper at power-on. Supply is 2.7 V to 5.5 V single ended or plus or minus 2.5 V to plus or minus 2.75 V for bipolar operation, over -40 C to +125 C. It is on the analog and mixed-signal IC line card.

Resolution against tolerance

Fifty kilo ohms over 1024 positions is 48.8 ohm per step. The plus or minus 1 percent end to end tolerance is 500 ohm, which is 10.2 codes at the bottom of the range. In other words the part resolves 48.8 ohm steps but only knows its total resistance to within about ten steps. That is why the family is sold for open loop and calibration use where the wiper setting is trimmed against a measurement, not for circuits that assume the programmed code alone sets the resistance.

ParameterFigureConsequence
Positions102448.8 ohm per step on 50 kohm
End to end toleranceplus or minus 1 percent500 ohm, 10.2 codes of uncertainty
Rheostat tempco5 ppm per degree C625 ppm over 125 C, 31 ohm
Memory50 times programmablea permanent setting that survives power cycling
Supply2.7 V to 5.5 V, or plus or minus 2.5 V dualruns in a bipolar signal path
InterfaceI2C with wiper readbackthe setting can be verified after a bus glitch

The 50 time memory is a budget, not a feature

Each permanent programming event consumes one of fifty fuse opportunities, and the action is irreversible, described by the vendor as equivalent to placing epoxy on a mechanical trimmer. A production fixture that programs the same board fifty one times has destroyed the part. The practical sequence is to adjust freely over I2C, confirm the value in the application, and blow one fuse at final test; anything that re-trims in the field should stay volatile and reload from the host at every power-up.

Selection notes

  • This is a two terminal rheostat, not a three terminal potentiometer. The wiper resistance is in series with the programmed value and is not published on the product page, so the minimum settable resistance has to come from the data sheet before it is used as a low value trim.
  • Power-on refresh comes from the 50 time memory. A part that has never been programmed powers up at a defined position only after the host writes it, so the host has to write before the circuit is used.
  • Bipolar operation at plus or minus 2.5 V allows the rheostat to sit in an AC signal path. Check the signal swing against the supply, because the terminals, not just the wiper, see the signal.
  • The MSOP body is 3 mm by 4.9 mm. The LFCSP alternative is 3 mm by 3 mm, a different order code and a different reflow profile.

Where it fits

Mechanical trimmer replacement, variable gain and offset adjustment in instrumentation, programmable filters and time constants, programmable current sources, sensor calibration and power supply trimming. The nonvolatile setting is what allows a calibrated instrument to keep its trim across a battery change.

Trim procedure at final test

Adjust over I2C as many times as the fixture needs, measure the result in the application, then program one fuse. The memory has fifty opportunities in total and each one is permanent, so a fixture that retries a failed programming step burns them quickly. Read the wiper back after every write, because a bus glitch during a write leaves the previous value in place and the fixture will record a pass on a setting that was never applied. A part that has never been programmed powers up at its default position, so the host has to write a known value before the circuit is used, or the fuse has to be blown at test so the power-on state is the calibrated one.

Questions buyers ask

Is 256 position version available? Yes, the AD5274 is the 256 position member of the family with the same interface. The 1024 position part is the one with finer steps at the same 50 kohm end to end value.

Does the wiper readback include the fuse state? It reports the current wiper setting. Whether the setting is volatile or loaded from memory is a separate status bit in the control register, which is worth reading at startup.

What does a quote need? The order code, the resistance value, the number of trims expected at final test and the annual quantity. Send it to the cost reduction desk where the trimmer is being replaced, or to the BOM desk for a scheduled build, and the reply carries the packing option for the RL7 reel.

Request Quote — In Stock, 100% New & Original, Full Warranty