Contact Us

AD1939YSTZRL

Brand: Analog Devices
Analog Devices AD1939YSTZRL is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD1939YSTZRL — Analog & Mixed-Signal ICs | Superb Automation

AD1939YSTZRL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD1939YSTZRL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD1939YSTZRL: Eight DACs and Four ADCs on One 3.3 V Rail, Differential Throughout

The AD1939 is a single chip audio codec with four analog to digital converters and eight digital to analog converters, 24 bit resolution, sample rates from 8 kHz to 192 kHz, and an on chip PLL that can derive the master clock from the left right clock or from an external crystal. Every analog input and output is differential, the serial ports support I2S, left justified, right justified and TDM, and a SPI port sets volume and routing. It runs from a 3.3 V digital and 3.3 V analog supply in a 64-lead LQFP, and the vendor lists it as qualified for automotive applications.

112 dB of DAC dynamic range against 107 dB on the converter side

The DAC path is specified at 112 dB of dynamic range and the ADC path at 107 dB, both A-weighted over a 20 Hz to 20 kHz band at 48 kHz. Those two numbers are within 5 dB of each other, which is the point of putting both converters on one die for a product that records and plays back through the same box. Total harmonic distortion plus noise is minus 94 dB, which is 0.002 percent, and that figure is low enough that the limit on a real board is the analog input network rather than the converter. Converted to bit depth, 107 dB of dynamic range is about 17.5 effective bits, so the 24-bit word length is a container and not a guarantee.

1.76 V rms differential is 4.96 V peak to peak, and that sets the headroom

The DAC full scale output is 1.76 V rms differential, which is 4.96 V peak to peak on each output pair, from a 3.3 V rail. That is possible only because the outputs are differential and the signal is centred between the two pins, so the single ended swing is half the differential figure. An engineer who measures one output against ground sees about 1.24 V peak and concludes the part is clipping, when in fact the pair is doing exactly what the data sheet says. The same arithmetic applies to the input side, and it is the reason a single ended source cannot be connected to one leg of a differential input without losing 6 dB and the even order cancellation.

ParameterValueWhat it decides
Converters4 ADC, 8 DACFour record and eight playback channels on one die
Resolution24 bitsWord length, not the delivered noise floor
Sample rate range8 kHz to 192 kHz48 kHz at 256 times is a 12.288 MHz clock
DAC dynamic range112 dB A-weightedAbout 18.3 effective bits over the audio band
ADC dynamic range107 dB A-weightedAbout 17.5 effective bits, the record side limit
Distortion plus noiseMinus 94 dB0.002 percent, the analog network dominates before this
DAC full scale1.76 V rms differential4.96 V peak to peak across the pair
ADC inputsDifferentialEven order terms cancel, common mode is rejected
Serial formatsI2S, left, right justified, TDMUp to 16 channels in and out on a TDM frame
Control portSPIVolume, mute, routing and power down from a host
Clock sourceOn chip PLL or crystalNo separate audio master clock needed on the board
Supply3.3 V digital and analogOne rail, and 5 V logic inputs are tolerated
Package64-lead LQFPDifferential routing on 0.5 mm pitch

The PLL is what removes a clock from the bill of materials

Deriving the audio master clock from the left right clock means the board does not need a second crystal or an audio grade oscillator, which is a real cost and a real board area saving on a small product. The penalty is jitter: a PLL that locks to a 48 kHz frame reference has to multiply it up to 12.288 MHz, and the resulting clock has more phase noise than a dedicated oscillator. On a playback path that is inaudible, and on a record path with a 107 dB converter it is measurable as a small loss of the top of the dynamic range. Where the product has an existing low jitter clock, using it directly is the better arrangement and the PLL becomes a fallback.

A codec with eight outputs is a channel count decision, not a stereo upgrade

Eight DAC channels are enough for a 7.1 playback path or for four stereo zones, and the TDM port is what carries that many channels over one wire to a digital amplifier or a DSP. Using four separate stereo codecs instead would consume four times the board area and four times the power, and would leave four converters to be matched against each other. The trade is that one codec failing takes the whole audio function with it, which matters in an automotive head unit where the part is qualified to the automotive standard precisely for that reason.

Buying a multichannel audio codec against an existing board

The order code fixes the package and the temperature grade, and the audio figures above belong to the whole part rather than to a selected grade. A second source for a part like this is rarely pin compatible, because the register map and the TDM frame format are vendor specific, so the substitution question is really a firmware question. Where the converter count is the reason for the change, the parts that can be compared on channel count and interface are listed in ADC DAC cross reference. Consolidating the analog and digital parts of one audio board onto fewer suppliers is covered in one stop BOM sourcing, and a shortage on a single audio part is handled through BOM shortage recovery.