Contact Us

HX339350

Brand: Hisiwell
Hisiwell HX339350 is a amplifiers & comparators component designed for Signal Conditioning & Filtering and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HX339350 — Amplifiers & Comparators | Superb Automation

HX339350

Hisiwell — Amplifiers & Comparators

Product Overview

The HX339350 from Hisiwell is a precision amplifier / comparator delivering high gain, wide bandwidth, and low distortion for signal conditioning. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High gain-bandwidth product for wideband signal amplification
  • Low input offset voltage and drift for precision DC applications
  • EMI-hardened design for robust operation in noisy environments
  • Rail-to-rail input/output for maximum dynamic range
  • Low quiescent current for power-sensitive designs
  • Unity-gain stable with capacitive load drive capability

Key Specifications

Channels—
GBWPMHz
Slew RateV/µs
VosµV
Iq per ChannelµA
Input Type—
Supply VoltageV
Operating Temp°C
Package—

Applications

Signal Conditioning & Filtering Current Sensing & Monitoring Data Acquisition Systems Audio & Video Processing Sensor Interface Amplifiers Industrial Control Loops

HX339350: 18 dB and 20 dBm at 42 to 47 GHz, with 7 dB of linearity headroom

The 42 to 47 GHz window is five gigahertz wide, which is narrow enough that a part can be optimised for gain and output rather than for bandwidth. The HX339350 takes that trade: 18 dB of small signal gain and 20 dBm of compression, 18 dBm minimum, from a 5 V rail at 200 mA, as a balanced die of 2.1 by 1.25 mm.

Published values

ParameterValue
Frequency range42 to 47 GHz
Small signal gain18 dB, flatness ±2 dB
Output P-1dB20 dBm typical, 18 dBm minimum
Output IP327 dBm at 44 GHz
Noise figure9 dB
Supply+5 V with negative gate, 200 mA, balanced
FormBare die, 2.1 x 1.25 x 0.1 mm, full passivation

Seven dB between intercept and compression

An output intercept of 27 dBm against 20 dBm of compression leaves 7 dB of spacing, which is tighter than the 10 to 13 dB seen in the low band parts. That spacing sets how much backoff a modulated signal needs: two tones at 14 dBm each put the products near 21 dBc down, and two tones at 17 dBm push them to about 15 dBc. For a single carrier link with a 20 dBm budget, the part is comfortable. For a multi carrier or a high order modulation signal, back off 3 to 4 dB and treat 16 dBm as the working output.

The two dB between typical and minimum

The catalogue gives 20 dBm typical and 18 dBm minimum compression. Two dB of spread is normal for a GaAs part at this frequency, and it means a link budget that assumes the typical figure has a 2 dB risk on the worst unit in a lot. In a production run, either buy against the minimum or ask for a tested screen. The same applies to the flatness figure of plus or minus 2 dB, which is the widest in this family: over a 5 GHz band that is fine for a single channel link and awkward for a channelised one.

What 200 mA buys at Q band

5 V at 200 mA is 1.00 W of DC, and 0.100 W of output at compression makes that 10 percent. The 0.90 W of heat is what the assembly has to carry, and at 40 degrees per watt the case to ambient rise is 36 degrees, so the part tolerates a modest ambient without a spreader. That combination, 18 dB of gain, 20 dBm and 1 W of DC, is why it appears in high density multi chip modules where the power budget per channel is one watt.

Two questions buyers ask

Is 18 dB enough for a single stage link? For a point to point radio with a mixer at minus 10 dBm output and a PA needing 15 dBm of drive, 18 dB covers it with margin. For a longer chain, two stages give 36 dB and 36 dBm of theoretical output, which the second stage cannot reach, so plan the output stage last and work backwards.

Does the negative gate have to be sequenced? Yes. The supply is listed as +5 V with negative gate, and the sequence is gate first, then drain, off in reverse. This is the failure mode that kills die during bring up, and it is worth writing into the test procedure rather than leaving to the operator.

SUPERB supplies the HX339350 with the vendor table and die drawing, and quotes it against scheduled demand with lot traceability. If you are comparing it against a packaged Q band amplifier, the amplifier cross reference hub lists the parameters that decide the swap. For lead time against a build plan, see component lead time solutions. Availability is listed under amplifiers and comparators.

Request Quote — In Stock, 100% New & Original, Full Warranty