Contact Us

TJA1051T/1J

Brand: NXP Semiconductors
NXP Semiconductors TJA1051T/1J is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1051T/1J — MCU & Embedded Processors | Superb Automation

TJA1051T/1J

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1051T/1J from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1051T/1J: SO8 CAN FD transceiver with pin 5 not connected

TJA1051T/1J is the plain SO8 member of the third generation line, with pin 5 left unconnected in the TJA1051 third generation high speed CAN transceiver line, described by Rev 9 of 28 November 2017. It is the same die as the /3 code with a different pin 5: nothing is connected there, which means the digital side runs from VCC and the transceiver has no way to be switched off from the controller. It is the cheapest member of the line and the one that shows up where the bus is always live.

Order code and package

Order codeTJA1051T/1J
Variant function on pin 5pin 5 not connected, so there is no VIO supply and no enable input
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5
Maximum data rate5 Mbit/s in the CAN FD fast phase
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on the /3 variants
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 9 of 28 November 2017

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentSilent mode 0.1 to 2.5 mA, normal recessive 2.5 to 10 mA and dominant 20 to 70 mA at 60 ohm
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance155 K/W junction to ambient in the SO8 body
Wake and diagnostic pinsPin 5 is the variant selector: not connected, VIO on the /3 codes or EN on the /E code, and there is no standby mode
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsdigital pins referenced to VCC internally, so a 3.3 V controller needs 5 V tolerant inputs
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

Without a VIO pin the digital interface sits at VCC, so a 3.3 V microcontroller has to present 5 V tolerant inputs on TXD and RXD and has to read a 5 V RXD. That works on most modern parts and fails on the ones whose absolute maximum on an I/O is VDD plus 0.3 V, which is a datasheet line worth checking before the BOM is frozen.

Pin 5 is not connected, so the silent mode that the /E code selects through its enable input is not available. The transmitter is always enabled while the part is powered, and the only way to stop it driving the bus is to drop VCC.

The difference between this code and the /3 code is one pin and one line of the ordering table. Both are 5 Mbit/s, both are ISO 11898-2:2016, both are 155 K/W in the SO8 body, and a substitution between them changes the digital interface while leaving every bus figure identical.

Bus pins stand minus 58 to plus 58 V and carry plus or minus 8 kV IEC 61000-4-2, unchanged from the rest of the line. On a 24 V system that is the rating that matters, since a short to battery with the supply off puts the full rail on the pin.

The delay from TXD to bus dominant is 65 ns typical and the low to low path is 60 ns, while the high to high path is specified as 40 to 250 ns. The three numbers are not interchangeable and a network timing budget has to use the window and not the typical value.

AEC-Q100 qualification and the dark green package finish are shared with the rest of the line, so the choice between the codes is a pin function question and never a quality question. A purchasing change from /3 to plain, or the reverse, is a board change and not a like for like swap.

Where this order code fits

It suits boards with a 5 V controller or a 3.3 V controller with 5 V tolerant pins, where the bus is always powered and no enable control is needed. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What is different between TJA1051T and TJA1051T/3? Pin 5. The /3 code has a VIO supply there, the plain code leaves it unconnected and references the digital pins to VCC. Every bus parameter is the same.

Does it support 5 Mbit/s CAN FD? Yes. The line is compliant with ISO 11898-2:2016 and timed for 5 Mbit/s in the CAN FD fast phase, independent of which pin 5 function the code carries.

Can the transmitter be turned off in software? Not on this code. Pin 5 is not connected, so there is no enable input and the only way to stop driving the bus is to remove VCC.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.