Contact Us

TJA1044T/1Z

Brand: NXP Semiconductors
NXP Semiconductors TJA1044T/1Z is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1044T/1Z — MCU & Embedded Processors | Superb Automation

TJA1044T/1Z

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1044T/1Z from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1044T/1Z: SO8 Mantis CAN transceiver limited to 1 Mbit/s

TJA1044T/1Z is the member of the Mantis line that is specified only to 1 Mbit/s in the TJA1044 Mantis high speed CAN transceiver line, described by Rev 8.0 of 6 November 2024. It is the T code of the Mantis line: classical CAN at up to 1 Mbit/s, with standby and wake-up, in the same package and with the same bus ratings as the CAN FD members. The single difference is that the loop delay symmetry parameters are not specified for it.

Order code and package

Order codeTJA1044T/1Z
Variant function on pin 5pin 5 is not a supply on this code; STB selects standby with host and bus wake-up
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2024 third edition, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate1 Mbit/s on the TJA1044T code and 5 Mbit/s in the CAN FD fast phase on every other variant
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.91 to 5.5 V on the variants that carry a VIO pin
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 8.0 of 6 November 2024

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby is a microamp class current with host and bus wake-up, and the VIO variants keep the wake receiver alive from VIO with VCC shut down
Electrostatic discharge8 kV IEC and 8 kV human body model on the bus pins
Thermal resistance94 K/W junction to ambient in the SO8 body
Wake and diagnostic pinsSTB input, host and bus wake-up, and a 0.5 to 1.8 s wake pattern filter on the C variant and on the VIO variants
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsdigital pins referenced to VCC, so a 3.3 V controller needs 5 V tolerant inputs
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

The document says TJA1044T is specified for data rates up to 1 Mbit/s and that the additional timing parameters defining loop delay symmetry are specified only for the other variants. A board that fits this part and later moves to a 2 Mbit/s data phase needs the other code, because the parameter does not exist here.

Everything else in the line is present: standby with host and bus wake-up, the ISO 11898-2:2024 physical layer, 4.5 to 5.5 V on VCC, minus 58 to plus 58 V on the bus and 8 kV on both the IEC and human body model tests.

Because the part is bought for 500 kbit/s and 1 Mbit/s networks, the timing budget is generous and the propagation delay window is not the limiting term. What does limit such a network is the stub length and the termination, and neither changes between the variants.

There is no VIO pin, so the digital side sits at VCC and a 3.3 V controller depends on 5 V tolerant inputs. The document states that condition explicitly for the non-VIO variants in this line.

The wake pattern filter on the C variant and on the VIO variants is 0.5 to 1.8 s and meets classical CAN and CAN FD requirements. On this code the filter is the classical figure, so a controller that sends a CAN FD style wake pattern has to be checked against it rather than assumed.

The SO8 body is 94 K/W and the dominant current is the same family figure, so the thermal arithmetic is identical to the faster codes: 350 mW at 70 mA and 5 V, 33 C of rise, 118 C junction at an 85 C ambient.

Where this order code fits

It stays in demand for classical 500 kbit/s and 1 Mbit/s networks that were specified against the 2024 standard and for repair of boards built around it. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Does TJA1044T work at 2 Mbit/s? No. It is specified to 1 Mbit/s and the loop delay symmetry parameters are only specified for the other variants in the line.

Is it otherwise the same part as TJA1044GT? Yes for the physical layer, the package, the bus ratings and the standby mode. The difference is the data rate specification and the interface pin on pin 5.

What replaced it on new 5 Mbit/s boards? The B, C and G variants of the same line, which add the timing parameters for the CAN FD fast phase.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.