TJA1044BT/0
Product Specifications
TJA1044BT/0
NXP Semiconductors — MCU & Embedded Processors
Product Overview
The TJA1044BT/0 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TJA1044BT/0: SO8 Mantis CAN FD transceiver without a VIO pin
TJA1044BT/0 is the SO8 member of the Mantis line with the shorter delay of the B variant and no VIO pin in the TJA1044 Mantis high speed CAN transceiver line, described by Rev 8.0 of 6 November 2024. It is the B variant without a VIO pin: 5 Mbit/s timing against the third edition of ISO 11898-2, a standby mode with host and bus wake-up, and a shorter propagation delay than the G variant, at the cost of a 3.3 V interface that depends on the controller being 5 V tolerant.
Order code and package
| Order code | TJA1044BT/0 |
| Variant function on pin 5 | pin 5 is not a supply on this code; the STB input selects standby with host and bus wake-up |
| Package | SO8, 3.9 mm body width, 8 pins |
| Protocol | ISO 11898-2:2024 third edition, SAE J2284-1 to SAE J2284-5 and SAE J1939-14 |
| Maximum data rate | 1 Mbit/s on the TJA1044T code and 5 Mbit/s in the CAN FD fast phase on every other variant |
| Supply voltage on VCC | 4.5 to 5.5 V |
| Logic supply on VIO | 2.91 to 5.5 V on the variants that carry a VIO pin |
| Temperature range | minus 40 to plus 150 C virtual junction |
| Qualification | AEC-Q100 |
| Datasheet | Rev 8.0 of 6 November 2024 |
Electrical parameters that decide the application
| Bus fault voltage | minus 58 to plus 58 V on CANH and CANL |
| Supply current | Standby is a microamp class current with host and bus wake-up, and the VIO variants keep the wake receiver alive from VIO with VCC shut down |
| Electrostatic discharge | 8 kV IEC and 8 kV human body model on the bus pins |
| Thermal resistance | 94 K/W junction to ambient in the SO8 body |
| Wake and diagnostic pins | STB input, host and bus wake-up, and a 0.5 to 1.8 s wake pattern filter on the C variant and on the VIO variants |
| Bus pins | CANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one |
| Logic levels | digital pins referenced to VCC, so a 3.3 V controller needs 5 V tolerant inputs |
| Behaviour with the supply off | the transceiver disengages from the bus so an unpowered node does not load the network |
| Protection | TXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family |
| Ordering string | the suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order |
Points to check before this part goes on a BOM
The B variant carries the shorter propagation delay in the family table, which is the reason the larger topology claim exists. The gain is not in the data rate, which is 5 Mbit/s either way, but in the delay window that has to fit inside a bit at that rate.
Without a VIO pin the digital side runs at VCC, so a 3.3 V controller has to accept a 5 V RXD and drive a 5 V referenced TXD. The document states that the non-VIO variants can work with 3.3 V controllers when the I/O are 5 V tolerant, which is a condition rather than a specification.
Standby keeps the wake receiver alive from VCC on this code rather than from VIO, so VCC cannot be removed if the node has to wake on the bus. That is the practical difference to the VIO variants, where the main rail can be switched off completely.
VCC is 4.5 to 5.5 V and the standby current is in the microamp class, so a node that sleeps for a year on this part spends tens of mAh, which is a rounding error against a 60 Ah battery and a real number against a 225 mAh coin cell.
The delay from TXD to bus dominant is 62 ns typical and 90 ns maximum on the B and C variants, with the recessive path at 75 ns typical. Those two numbers have to be added to the controller delay before the transmit sample point is chosen.
The SO8 body is 94 K/W, so the 350 mW of a 70 mA dominant bus is a 33 C rise. In an 85 C ambient the junction is at 118 C, which leaves 32 C of margin to the 150 C limit and no more than that.
Bus pins stand minus 58 to plus 58 V with 8 kV IEC 61000-4-2 and 8 kV human body model, so the surge and ESD numbers are the same on every code in the line and only the interface and the delay window change between them.
Where this order code fits
It is the choice on long or heavily stubbed networks at 5 Mbit/s where the controller already has 5 V tolerant pins and the main rail stays alive. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
What does the B variant add over the G variant? A shorter propagation delay, which is what allows larger network topologies at 5 Mbit/s. The data rate, the standby mode and the bus ratings are the same.
Can a 3.3 V controller drive it directly? Only if its I/O are 5 V tolerant, since there is no VIO pin on this code and the digital side sits at VCC. The variants with a VIO pin remove that condition.
Can VCC be switched off while it wakes on the bus? No. The wake receiver on this code runs from VCC, so removing the rail also removes the wake function.
SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.