Contact Us

TJA1043TK/1

Brand: NXP Semiconductors
NXP Semiconductors TJA1043TK/1 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1043TK/1 — MCU & Embedded Processors | Superb Automation

TJA1043TK/1

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1043TK/1 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1043TK/1: HVSON14 CAN FD transceiver with INH, ERR and listen-only

TJA1043TK/1 is the leadless HVSON14 member of the line that controls the node supply in the TJA1043 high speed CAN transceiver line with full node power control, described by Rev 6 of 10 November 2017. It is the leadless body of the same node controlling transceiver: the same INH, ERR, wake and listen-only functions with 44 K/W instead of 68 K/W. On a gateway board with a dozen rails the thermal margin and the area are usually why this code is chosen.

Order code and package

Order codeTJA1043TK/1
Variant function on pin 5STB, EN and WAKE inputs with INH and ERR outputs in a 3 x 4.5 mm leadless body
PackageHVSON14, 3 x 4.5 mm leadless, 14 pins
ProtocolISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5
Maximum data rate5 Mbit/s in the CAN FD fast phase
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on every code, since the part always carries a VIO pin
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 6 of 10 November 2017

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby and sleep currents are the lowest in this family, and listen-only mode draws the normal recessive current without driving the bus
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance44 K/W junction to ambient in the HVSON14 body
Wake and diagnostic pinsSTB, EN and WAKE inputs, INH output for the node regulator, ERR output for diagnostics and a listen-only mode
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsTXD, RXD, STB and EN referenced to VIO, which accepts 3 V to 5 V
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

44 K/W against 68 K/W is a 24 K difference at the 350 mW of a dominant bus. In an 85 C ambient the junction lands at 100 C here against 124 C in the SO14 body, and that difference is what allows the part to sit beside a switching regulator without a cut-out in the copper.

The leadless body is 3 x 4.5 mm against a 3.9 mm wide SO14 with 1.27 mm lead pitch. The pin count is the same, so the change from the wired code to this one is a footprint change and nothing else, and the netlist does not move.

INH still switches the node regulator and ERR still reports bus faults, so a board that moves from the SO14 code keeps the wake behaviour, the diagnostic and the listen-only mode without a firmware change.

The exposed pad is the thermal path and it is not connected to any signal, so it can be tied to ground for a quiet plane or left on a dedicated pad. Either way it needs vias, and the 44 K/W figure assumes a soldered pad.

Bus pins stand minus 58 to plus 58 V with plus or minus 8 kV IEC 61000-4-2, unchanged from the wired body. A 24 V network with a short to battery is inside the rating and a 48 V network is not.

Leadless assembly needs the optical inspection capability the document names, and a reflow profile with a controlled ramp for the 0.85 mm body. Houses that already run HVSON or DFN parts in volume will not notice the change; houses that do not should stay on the SO14 code.

Where this order code fits

It goes on gateways and body controllers where the board is dense and the transceiver shares copper with a regulator, and where leadless assembly is already in place. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Supplier Quality Audit page.

Questions buyers ask

Is TJA1043TK/1 a drop in for TJA1043T/1? Electrically yes, physically no. The pin count and the functions match and the body is a 3 x 4.5 mm leadless package instead of an SO14, so the footprint changes.

How much better is the thermal path? 44 K/W against 68 K/W junction to ambient, which is 24 K at the 350 mW of a dominant bus, on condition that the exposed pad is soldered with vias.

Does it keep the INH and ERR functions? Yes. Both outputs, the wake inputs and the listen-only mode are identical to the wired code.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.