Contact Us

TJA1042T/3/1

Brand: NXP Semiconductors
NXP Semiconductors TJA1042T/3/1 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1042T/3/1 — MCU & Embedded Processors | Superb Automation

TJA1042T/3/1

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1042T/3/1 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1042T/3/1: SO8 CAN FD transceiver with standby and a VIO pin

TJA1042T/3/1 is the SO8 member of the standby line with a VIO pin on pin 5 in the TJA1042 high speed CAN transceiver line with standby mode, described by Rev 7 family document. It carries the ISO 11898-2:2016 physical layer at 5 Mbit/s and adds what the TJA1051 line does not have: a standby mode that wakes on a bus pattern, and a VIO pin so the digital side follows a 3.3 V controller. The combination is what most body control modules settle on.

Order code and package

Order codeTJA1042T/3/1
Variant function on pin 5VIO input on pin 5; standby is selected by the STB input
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2016, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate5 Mbit/s in the CAN FD fast phase, with shorter propagation delay on the B and C variants
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on the /3 variants
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 7 family document

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, normal recessive 2.5 to 10 mA and dominant 20 to 70 mA
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance92 K/W junction to ambient in the SO8 body, 53 K/W for the HVSON8 body
Wake and diagnostic pinsSTB input selects standby with bus wake-up, pin 5 is SPLIT on the plain codes and VIO on the /3 codes
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsTXD, RXD and STB referenced to VIO, which accepts 2.8 to 5.5 V
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

Standby current is 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, so the two supplies have to be budgeted together: 15 microamps on one rail and 14 on the other is 254 mAh across a year, not the 131 mAh the VCC figure alone suggests.

The wake pattern is the ISO 11898-2:2016 one, a dominant phase followed by a recessive phase with a minimum time-out of 0.8 ms per SAE J2284 while ISO leaves 0.3 ms open for legacy parts. A controller that sends a shorter pattern will not wake the node, and that is the most common integration fault on this part.

Normal mode draws 2.5 to 10 mA recessive and 20 to 70 mA dominant into 60 ohm. At 70 mA and 5 V the part dissipates 350 mW, which is a 32 C rise in the SO8 body and lands at 117 C in an 85 C ambient, inside the 150 C limit with room for the regulator next to it.

Pin 5 is VIO on this code and the SPLIT output on the plain codes, which is the difference that matters when a board is copied. A net tied to pin 5 for split termination has to be removed before the /3 part is placed, otherwise the termination midpoint is driven by a supply.

The B and C variants of the line have shorter propagation delay than the A variant, and a network that grows beyond a few metres of stub at 2 Mbit/s and above is where that shows. This code is the base variant, so the delay window is the wider one.

Bus pins stand minus 58 to plus 58 V with plus or minus 8 kV IEC 61000-4-2. The 58 V figure is a DC rating with no time limit, which is what allows the part to sit on a 24 V network where a short to battery is a permanent condition rather than an event.

Where this order code fits

It is the usual choice for a 3.3 V body control module that has to wake on bus traffic, and it is the part most often compared against the TJA1043 when the node also has to switch its own supply. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Does TJA1042T/3 wake from the bus? Yes, in standby mode, on the ISO 11898-2:2016 wake pattern with the 0.8 ms per phase time-out that SAE J2284 requires. A shorter dominant pulse will not wake the part.

What does pin 5 do on this code? It is a VIO supply input, 2.8 to 5.5 V, so the digital pins follow the controller rail. The plain TJA1042T codes put the SPLIT output on that pin instead.

How much does the part draw in standby? 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, so both rails count towards the sleep budget.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.