Contact Us

TJA1021T/20/CM

Brand: NXP Semiconductors
NXP Semiconductors TJA1021T/20/CM is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1021T/20/CM — MCU & Embedded Processors | Superb Automation

TJA1021T/20/CM

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1021T/20/CM from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1021T/20/CM: SO8 LIN transceiver with the 20 kBd normal slope

TJA1021T/20/CM is the SO8 LIN transceiver set to the normal slope for 20 kBd in the TJA1021 LIN transceiver line, described by Rev 4 family document. It is the interface between a LIN commander or responder controller and the single wire bus, compliant with LIN 2.0 through 2.2A, SAE J2602 and ISO 17987-4, with the output slope set for the 20 kBd maximum rate. The integrated responder termination means a sensor node needs no external 30 kohm resistor.

Order code and package

Order codeTJA1021T/20/CM
Variant function on pin 5SLP_N input with an INH output; the /20 suffix is the normal slope setting
PackageSO8, 3.9 mm body width, 8 pins
ProtocolLIN 2.0, 2.1, 2.2, 2.2A, SAE J2602 and ISO 17987-4:2016 (12 V)
Maximum data rate20 kBd on the /20 and B codes and 10.4 kBd on the /10 and A codes
Supply voltage on VCC5.5 to 27 V on VBAT
Logic supply on VIOnot present; inputs are compatible with 3.3 V and 5 V logic
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 4 family document

Electrical parameters that decide the application

Bus fault voltageminus 40 to plus 40 V on LIN and VBAT as a limiting value
Supply currentSleep mode battery current 2 to 10 microamps with the LIN pin at battery and the wake pin high
Electrostatic dischargeplus or minus 6 kV IEC 61000-4-2 on LIN, VBAT and WAKE_N
Thermal resistance93 K/W junction to ambient in the SO8 body, 54 K/W for the HVSON8 body
Wake and diagnostic pinsSLP_N input, INH output, local and remote wake-up with source recognition, and an integrated responder termination
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsinputs compatible with 3.3 V and 5 V devices
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

Battery current in sleep mode is 2 to 10 microamps with the LIN pin at battery and the wake pin high. At the maximum figure that is 87.6 mAh across a year, which is why a LIN node can sit on a vehicle battery for months without a disconnect.

The 20 kBd slope is the fast setting, and the same die in the /10 code is set for 10.4 kBd to meet SAE J2602. Putting the fast part on a J2602 network is the usual cause of emission failures, because the steeper edges are what the standard is trying to limit.

The responder termination is internal, so the pin count stays at eight and the node does not need the external resistor and diode that a discrete interface would carry. A commander node still needs its own 1 kohm pull-up and series diode.

Wake-up source recognition separates a local wake on the WAKE_N pin from a remote wake on the bus, which lets the controller tell an ignition event from a bus message without extra wiring.

Electrostatic discharge is plus or minus 6 kV IEC 61000-4-2 on LIN, VBAT and WAKE_N, and the LIN pin is short circuit proof to battery and ground. On a single wire bus that runs to a door or a mirror, those two lines are the ones that decide field returns.

The part is pin compatible with the TJA1020 and the MC33662(B), which is why it turns up as a second source on boards that were drawn for either. Pin compatibility covers the pins and not the slope setting, so the /10 and /20 codes have to be checked against the network they land on.

Where this order code fits

It is the standard part for LIN sensor and actuator nodes at 20 kBd, and for boards that were drawn against the TJA1020 pinout and need a pin compatible replacement. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does a responder node need an external termination resistor? No. The 30 kohm responder termination is integrated, so a sensor node needs only the transceiver and its decoupling.

Can the /20 code be used on a SAE J2602 network? It is the fast slope part. J2602 networks belong on the /10 code, which is set to 10.4 kBd and limits the edge rate the standard is concerned about.

What current does it draw in sleep? 2 to 10 microamps on VBAT, which is 87.6 mAh across a year at the maximum figure.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.