Contact Us
  • Home
  • COMPONENTS
  • NTC Thermistors and Temperature Probes for Industrial Sensing

NTC Thermistors and Temperature Probes for Industrial Sensing

10 k NTC thermistors in 0402, 0603 and wire lead probe form, with B values from 3380 K to 3988 K and a tolerance down to 1 percent on the resistance value.
quote now

Product Specifications

NTC thermistors and temperature probes for industrial sensing

Product Overview

An NTC thermistor is a resistor whose value falls as it warms, and the curve is described by a B value rather than by a straight line. Two parts can both be 10 k at 25 C and still read differently at 80 C if their B values differ, which is why the B value and its tolerance belong next to the resistance in any comparison. A 3380 K part and a 3960 K part are not interchangeable above about 40 C even though both carry the same 10 k label.

Tolerance is the second number. A 1 percent part at 25 C is worth about 0.25 C at room temperature, and that error grows as the curve steepens, so a probe that has to hold half a degree at 80 C needs both a tight resistance and a tight B. The parts on this page are ordered by that: the chip thermistors with 1 percent on both figures, the glass protected parts with the same tolerance and a wider temperature range, and the wire lead probes that put the bead at the end of an insulated lead so the measurement point can be inside a housing.

The thermal path decides the last part of the choice. A 0402 chip responds in a second or two on a thin board, but it measures the board as much as the air, so it is used for compensation rather than for sensing a medium. A wire lead probe with a 2.8 mm bead has a time constant of a few seconds in still air and much less in a flowing liquid, and its dissipation constant sets how much current the divider can push through it before self heating becomes an error. A rule of thumb is to keep the measurement current low enough that the self heating stays under a tenth of a degree.

Key Specifications

ParameterChip thermistor 0402Glass protected 0603Wire lead probe
Resistance at 25 C10 k10 k10 k
B value3380 K at 25/50 C3435 K at 25/85 C, 3960 K option3988 K at 25/100 C
Tolerance1 percent on resistance and on B1 percent on resistance and on B1 percent on resistance
Maximum power at 25 C100 mW125 mW60 mW
Dissipation constant1.0 mW per C3.0 mW per K1.5 mW per K
Thermal time constantabout 2 s in still airunder 4 s in still airabout 15 s in still air
Operating range-40 C to 125 C-55 C to 150 C-55 C to 155 C
Form0402 chip0603 chip, glass coatedbead on PTFE insulated wire

Included Models and Order Codes

The order codes below are the thermistors quoted most often for battery packs, power supplies, HVAC probes and industrial controllers. State the resistance at 25 C, the B value, the tolerance, the temperature range and the mounting, and the part and its divider resistor are confirmed together.

Part NumberResistance at 25 CB ValueTolerancePackage or FormNotes
NCP15XH103F03RC10 k3380 K at 25/50 C1 percent0402 chip100 mW, 1.0 mW per C
NCP18XH103F03RB10 k3380 K at 25/50 C1 percent0603 chipreel packing for reflow
NTCG103JF103FT110 k3380 K at 25/50 C, 3435 K at 25/85 C1 percent0603 chip100 mW, 310 uA maximum
NTCS0603E3103FMT10 k3435 K at 25/85 C1 percent0603 chip, glass protected125 mW, AEC-Q200
NTCS0603E3103FHT10 k3960 K at 25/85 C1 percent0603 chip, glass protected125 mW, AEC-Q200
B57861S0103F04010 k3988 K at 25/100 C1 percentwire lead bead, 50 mm60 mW, -55 C to 155 C
103AT-210 k3435 K1 percentwire lead bead, 2.8 mmgeneral purpose probe element

Key Features

B value next to resistance – every row gives the B value and the temperature pair it was measured over, because two 10 k parts with different B values separate above 40 C.

Tolerance on both figures – 1 percent on resistance and 1 percent on B is stated separately, which is what a half degree budget at 80 C actually needs.

Package selects the thermal path – 0402, 0603 and wire lead parts are listed as separate rows, because the time constant and the dissipation constant follow the package, not the material.

Glass protected for harsh media – the protected 0603 parts hold 125 mW and cover -55 C to 150 C, which is what a potted assembly or an engine bay needs.

Automotive qualification flagged – AEC-Q200 parts are marked in the notes, so a part for a vehicle harness is never substituted with a commercial chip of the same value.

Self heating worked out – the maximum current is given on the chip rows, so the divider can be sized to keep the self heating under a tenth of a degree.

Wire lead for remote sensing – a 50 mm bead on insulated wire puts the sensing point inside a housing while the board stays outside it, which is the usual arrangement in a probe assembly.

Curve data available – the resistance ratio table is published by the maker for each B value, so the firmware table can be built from measured data rather than from a single point.

Applications

These parts are quoted for temperature measurement and compensation inside equipment, typically where: The thermistor sits in a divider next to the controller, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board and its matching resistor.

Battery packs and chargers – a 10 k chip against a fixed resistor gives a divider the charger can read, and the 1 percent tolerance keeps the cutoff point consistent from unit to unit.

Power supplies and motor windings – a glass protected part on a hot spot flags an over temperature condition, and its 150 C range covers the winding insulation class.

HVAC and appliance probes – a wire lead bead inside a stainless sleeve measures air or water, and the insulated lead keeps the board away from the medium.

Industrial controllers and instruments – a chip part next to a reference or an amplifier compensates drift, where the board temperature is the quantity that matters rather than the air.

Sourcing and Cross-Reference

Thermistors are the cheapest part on most boards and the one most often substituted without a check, which is why field failures cluster around them. A 10 k part with a 3380 K curve replaced by a 10 k part with a 3960 K curve reads about 4 C high at 60 C, and nothing in the part number warns about it. The B value and the temperature pair it was measured over are the two fields that have to match.

The second field is the package. A chip part and a wire lead probe are not interchangeable even at the same resistance and the same B, because the thermal time constant changes by an order of magnitude. A controller tuned around a fast chip will overshoot with a slow probe, and a probe that is meant to sit in a liquid will read the air if it is replaced by a board mount part.

Supply is stable for the common values and thinner for the tight tolerance and automotive grades, which are bought against a forecast. The quotation line states the tolerance, the B value, the package and the batch date, and for a medical or an automotive build the lot traceability is kept with the shipment.

For volume builds, SUPERB Assembly support covers the divider resistor pairing, the potting clearance around a wire lead bead and the reflow profile for glass protected chips.

Q: Can you supply a 10 k NTC with the same B value when the original part is unavailable?

A: Yes. Send the current part number, the resistance at 25 C, the B value and the temperature pair it was measured over, and the SUPERB Tech sales team will confirm the nearest part that keeps the curve and the package.

Why Buyers Source NTC Thermistors Through SUPERB

  1. Curve matched, not just value: the B value and the measurement pair are compared, so a substitute does not read several degrees off at the top of the range.
  2. Package and response time: chip, glass protected and wire lead forms are quoted apart, because the time constant decides how the control loop behaves.
  3. Divider resistor paired: the fixed resistor is quoted with the thermistor so the divider ratio and the self heating are correct at the first build.
  4. Automotive grades tracked: AEC-Q200 parts are flagged in the notes, so a vehicle build never receives a commercial chip with the same printed value.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and detectors, Temperature and humidity sensors, Industrial pressure sensors, 24-bit delta-sigma ADCs, Pin to pin cross reference.