Contact Us

UCC5350MCDR

Brand: Texas Instruments
Texas Instruments UCC5350MCDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC5350MCDR — Power Management & Signal Chain | Superb Automation

UCC5350MCDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC5350MCDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC5350MCDR: isolated single channel gate driver with an active Miller clamp

UCC5350MCDR is a galvanically isolated gate driver that sits across the isolation barrier of a motor drive or an industrial supply in a SOIC (D) body of 8 pins. The M option adds an active Miller clamp, which holds the gate low through the fastest part of the switch node transition and stops the spurious turn on that a displacement current can trigger. The driver sources and sinks 5 A minimum and 10 A typical, with 60 ns of propagation delay and 100 kV per microsecond of common mode transient immunity.

Order code and package

Order code read outUCC5350 M C D R: device UCC5350, M Miller clamp option, C 12 V output UVLO, D eight pin SOIC, R large tape and reel
PackageSOIC (D), 8 pins, 4 mm of creepage, with an 8.5 mm DWV body available for higher isolation
Isolation rating3 kVRMS for the D package, against 5 kVRMS for the DWV body
Carrier in the vendor addendum2500 pieces on a large reel for the D rows, 1000 pieces for the DWV rows
Moisture levelLevel 2, 260 degrees, one year floor life
Lead finishNickel palladium gold, with a call vendor note on some rows
Operating temperatureminus 40 to plus 125 degrees

Electrical parameters that decide the application

Input supply3 V to 15 V on the primary side, which lets a 3.3 V or 5 V controller drive it directly
Driver supplyUp to 33 V on the secondary side, with 8 V and 12 V undervoltage options across the family
UVLO versionThe C suffix selects the 12 V output UVLO, with turn on at 12 to 13 V and turn off at 10.3 to 11 V
Peak source current5 A minimum and 10 A typical for the M option
Peak sink current5 A minimum and 10 A typical for the M option
Propagation delay60 ns typical, matched between the rising and falling paths
Common mode transient immunity100 kV per microsecond minimum, which is the figure that survives a fast motor phase node
Miller clamp threshold2.1 to 2.3 V, so the clamp engages just above the gate threshold rather than at zero
Miller clamp level26 to 50 mV at a 20 mA clamp current, with 5 to 10 A of clamp current capability
Input bias current1.67 mA typical on the primary supply and 1.1 mA on the driver supply
Isolation lifeThe vendor quotes more than 40 years of barrier life under the rated working voltage
Absolute maximum18 V on the input supply, 35 V across the driver supply, 17.5 V of negative bias on the E version

Family options and how they differ

UCC5350MCthe part on this page, Miller clamp with the 12 V UVLO
UCC5350Ssplit output instead of a clamp, for controlling rise and fall times separately
UCC5310MCthe lower current member with the same clamp, for smaller dies
UCC5390the 10 A family member, for modules with a large gate charge
D and DWV bodies4 mm and 8.5 mm of creepage, 3 kVRMS against 5 kVRMS, chose by the creepage the application needs

Points to check before this part goes on a BOM

The clamp is there for a specific failure that a plain driver cannot prevent. When the opposite switch in a bridge turns on, the switch node moves at several kilovolts per microsecond, and the gate to drain capacitance couples that displacement current into the gate of the off device. If the gate resistor is large or the driver is far away, the gate rises above threshold and both switches conduct at once. The clamp holds the gate at 26 to 50 mV through that window and sinks 5 to 10 A if it has to.

The C suffix on this order code is the UVLO version, not a revision. With a 12 V secondary supply the turn on threshold sits at 12 to 13 V, which means the driver refuses to switch until the gate drive rail is fully formed. An 8 V UVLO version exists in the same family for a lower drive level, and the two are not interchangeable on a board that expects a particular rail.

Isolation ratings are package dependent, and the order code carries the package. The D body gives 4 mm of creepage and 3 kVRMS, which covers most 400 V and 600 V motor drive work, while the DWV body gives 8.5 mm and 5 kVRMS for higher working voltage. A substitution between the two changes the creepage on the board, so it is not a drop in move even though the die is the same.

The 100 kV per microsecond common mode transient immunity is the number to compare against an optocoupler. An optocoupler of the same current class typically manages a fraction of that, and the difference shows up as bit errors or spurious turn off at high switching dv/dt. For a silicon carbide or gallium nitride bridge running at high bus voltage, that immunity is the reason the part exists.

Bias current on the primary side is 1.67 mA typical and on the driver side 1.1 mA, which is small enough that a bootstrap or a small isolated supply can feed several channels. The number that catches people out is the gate charge current, not the quiescent current: at 20 kHz with a 1 uC gate charge the driver delivers 20 mA, which is more than ten times the quiescent figure and has to come from the isolated rail.

Where this order code fits

Used in motor drives, servo amplifiers, industrial inverters, solar and storage converters, uninterruptible supplies and any bridge that needs a galvanically isolated gate drive with a clamp for fast switching devices. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What does the M option add? An active Miller clamp on the gate. It holds the gate below 50 mV once the driver output goes low, which prevents a spurious turn on when the opposite switch moves the node at high dv/dt.

Which UVLO version is this part? The 12 V version, selected by the C in the order code. Turn on is at 12 to 13 V and turn off between 10.3 and 11 V, which suits a 15 V gate drive rail with margin.

Can it drive a silicon carbide module? Yes, the family is specified for MOSFET, IGBT, SiC and GaN devices, with the 5 A drive suited to a module gate charge. The isolated rail has to supply the gate charge current at the switching frequency.

Is the DWV body a drop in replacement? No. It is wider and gives 8.5 mm of creepage against 4 mm, so the land pattern and the clearance on the board both change. The die and the behaviour are the same, the isolation is not.

How is it different from an optocoupler driver? Propagation delay is 60 ns against several hundred for an optocoupler, the common mode immunity is 100 kV per microsecond minimum, and the barrier life is quoted above 40 years. The trade is that the part needs two supplies.

How much isolated supply current is needed? Enough for the gate charge at the switching frequency plus the 1.1 mA quiescent current. At 20 kHz with 1 uC of gate charge that is 20 mA, and the isolated rail has to hold its voltage through the peak of the switching event.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.