UCC2805DTR
Product Specifications
UCC2805DTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC2805DTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC2805DTR: a 50 per cent duty current mode PWM controller with a 4 V reference and a 4.1 V start threshold, for converters that run from a 5 V or battery bias rail, in the eight pin SOIC on a 2500 piece reel
UCC2805DTR is a fixed frequency peak current mode controller that drives the gate of an external FET directly from a bias rail that may sit as low as 4.1 V, with a trimmed 4 V reference for the feedback divider and a second, higher current sense threshold for cycle by cycle limiting in a SOIC body of 8 pins. The D body is the eight pin SOIC measuring 4.90 mm by 3.91 mm, and the DTR string is tape and reel. This is the member of the family with both the low lockout and the 4 V reference, which is the pair that decides whether a converter will start on a five volt rail.
Order code and package
| Catalogue string | UCC2805DTR, where 2805 is the 50 per cent duty member with the 4 V reference and the 4.1 V start threshold, D is the eight pin SOIC and TR is tape and reel |
| Body | SOIC, D outline, eight pins, 4.90 mm by 3.91 mm, the same footprint as every other member of the family so a swap does not touch the board |
| Reel | 2500 pieces on a 330 mm reel in the carrier table, while a second table in the same document prints 2000 for the same string, so the reel size has to be named on the order |
| Status | Active in production on the current addendum, while the .A row of the same string is listed Obsolete, so the plain DTR string is the one to buy |
| Temperature | minus 40 to 125 C, and the electrical table is specified over that range with the ambient held equal to the junction |
| Finish and moisture | NIPDAU plating at moisture level 1 for 260 C with no floor life limit, which suits a line that opens a bag and does not finish it the same week |
| Reference | 4 V, not 5 V. The 2805 and the 2803 are the two members that carry the 4 V reference, and the divider on the feedback pin has to be built for that number |
| Document | SLUS270H, first issued March 1999 and revised April 2025, a document that has been maintained continuously since the part was introduced |
| Pins | COMP on pin 1, FB on pin 2, CS on pin 3, RC on pin 4, ground on pin 5, OUT on pin 6, VCC on pin 7 and REF on pin 8 |
Electrical parameters that decide the application
| Bias range | 12 V absolute maximum on VCC, which is a hard ceiling for this family and is well below the rail that the 2802 and 2804 members tolerate through their internal clamp |
| Start threshold | 3.7 V minimum, 4.1 V typical and 4.5 V maximum, measured with the bias ramping up, so a four cell alkaline pack or a five volt rail starts the controller directly |
| Stop threshold | 3.2 V minimum, 3.6 V typical and 4.0 V maximum, giving 0.5 V of hysteresis so a rail sagging under a load step does not restart the converter |
| Maximum duty cycle | 48 per cent minimum, 49 per cent typical and 50 per cent maximum, produced by the internal toggle flip flop that blanks every other clock |
| Oscillator | 26 kHz minimum, 31 kHz typical and 36 kHz maximum with RT at 100 k and CT at 330 pF, and on this member the oscillator runs at twice the switching frequency, so the gate sees about 15.5 kHz |
| Current sense gain | 1.65 V per volt typical, with a 1.1 to 1.8 window, and the maximum input signal is 1 V at COMP held at 5 V |
| Over current threshold | 1.55 V typical with a 1.42 to 1.68 V window, which is a separate comparator from the PWM ramp and terminates the pulse on its own |
| Sense timing | 100 ns of blanking after the gate turns on, and 0.9 V of offset between COMP and CS, so the current loop has no authority until the error amplifier rises past that level |
| Output stage | totem pole, plus or minus 1 A peak and 20 microjoules of capacitive load energy, with 0.4 V of low level at 20 mA and 0.9 V at 200 mA |
| Switching times | 41 ns rise and 44 ns fall typical into 1 nF, with 70 ns and 75 ns at the maximum end of the window |
| Supply current | 0.2 mA in the start state, and 0.5 mA typical and 1 mA maximum while running, which is what makes a resistor from a high rail a usable start path |
| Soft start | the error amplifier output climbs from 0.5 V to the reference in 4 ms typical and 10 ms maximum, set internally with no external capacitor |
| Error amplifier | 2 V input threshold on this member rather than the 2.5 V of the 2800 and 2801, 80 dB of open loop gain and 2 MHz of gain bandwidth |
| Thermal | 117.9 C per watt junction to ambient in the eight pin SOIC body, which sets the practical limit on how much gate charge can be driven at high ambient |
Family variants and how they differ
| UCC2800 | 100 per cent duty, 5 V reference, 7.2 V start and 6.9 V stop, the general purpose member for offline bias windings |
| UCC2801 | 50 per cent duty, 5 V reference, 9.4 V start and 7.4 V stop, for a converter that has to hold off at low line |
| UCC2802 | 100 per cent duty, 12.5 V start and 8.3 V stop, with a 13.5 V internal shunt so it can be fed through a resistor from a high rail |
| UCC2803 | 100 per cent duty with the 4 V reference and the 4.1 V start of this member, which is the choice when full duty is wanted on a five volt rail |
| UCC2804 | 50 per cent duty with the 12.5 V start and 8.3 V stop, the offline counterpart of this part |
| UCC2805 | 50 per cent duty, 4 V reference, 4.1 V start and 3.6 V stop, the part on this page |
| Temperature grades | the 1805 covers minus 55 to 125 C, the 2805 minus 40 to 125 C and the 3805 zero to 70 C on the same die and the same pinout |
| Pin compatibility | all six members share the eight pin map, so a duty cycle or lockout change is a straight swap with no board change and no change to the compensation network |
Points to check before this part goes on a BOM
The 4 V reference with the 3.6 V stop threshold is the pair that matters on a five volt rail. The controller starts at 4.1 V and keeps running down to 3.6 V, so a rail that collapses during a load step does not restart the converter, and the reference stays inside regulation across that whole window, which is the reason this member exists rather than the 5 V reference versions.
The oscillator on this member runs at twice the switching frequency, and the data sheet states it in a footnote rather than in the table. Reading the 46 kHz typical from the 2800 and 2804 rows and applying it here gives half the frequency that was intended, and the transformer or inductor is then sized for the wrong ripple. Set RT and CT from the 31 kHz row and expect about 15.5 kHz at the gate.
The COMP to CS offset of 0.9 V is a working limit, not a detail. Until the error amplifier output rises past that level the current loop commands nothing, so the converter runs at the minimum on time the gate driver and the propagation delay allow, which at light load is the burst of narrow pulses that shows up as audible noise on some magnetics.
There is no internal shunt regulator on this member, unlike the 2802 and 2804 which clamp at 13.5 V. The absolute maximum on VCC is 12 V, so a start resistor from a rectified mains has to stop conducting once the auxiliary winding takes over, or the bias has to come from a regulated rail.
The output is actively held low while the bias is below the lockout threshold, which removes the gate to source bleeder resistor that older bipolar controllers needed. On a repair bench this is also why a controller with a dead bias reads as a short from gate to source rather than as an open.
The addendum prints two different reel quantities for UCC2805DTR, 2500 in the carrier table and 2000 in the packaging table, and the body column in that older file sits one row off, so the TSSOP string appears against the SOIC part number. Both are worth confirming on the offer rather than assuming from the text.
Decoding the ordering string
UCC2805 is the device: 2 is the industrial temperature grade, 805 is the 50 per cent duty member with the 4 V reference. D is the eight pin SOIC, T is tape and the R is the reel. The same die in the TSSOP body ends in PW or PWR, and the two bodies do not share a reel size.
There is no Q1 or E suffix on this string. Where a supplier offers an automotive or extended version of this family, it carries a different order code and a different qualification document, so a cross reference that stops at the base number is not a confirmed substitute.
Where this order code fits
Low voltage offline converters, standby and housekeeping supplies, battery fed step up and flyback stages, and instrument power rails where the controller has to start below five volts and keep running through a sag Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Why choose the 2805 over the 2802? The 2802 starts at 12.5 V and needs a bias rail high enough for that, while this part starts at 4.1 V and runs down to 3.6 V. On a five volt or battery rail the 2802 simply will not start.
What switching frequency should be expected? With RT at 100 k and CT at 330 pF the oscillator sits at 31 kHz typical, and the output runs at half that, about 15.5 kHz. The oscillator frequency is not the gate frequency on this member.
Is the 4 V reference a problem for a 3.3 V output? No, the divider scales the output down to 4 V, and the reference holds 3.94 to 4.06 V at 25 C and 3.90 to 4.08 V over temperature, so a 3.3 V rail is set by a divider ratio rather than by the reference itself.
Can it drive a large MOSFET directly? It delivers plus or minus 1 A peak with 41 ns rise into 1 nF, which covers most TO-220 and D2PAK parts at moderate frequency. Above that the gate charge has to be checked against the 117.9 C per watt of the body.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.