Contact Us

UCC27511DBVR

Brand: Texas Instruments
Texas Instruments UCC27511DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27511DBVR — Power Management & Signal Chain | Superb Automation

UCC27511DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27511DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27511DBVR: single channel 4 A source and 8 A sink gate driver with a 13 ns propagation delay

UCC27511DBVR is a single channel low side gate driver in a 6 pin SOT-23 that sources 4 A and sinks 8 A into a MOSFET gate with a 13 ns typical delay and a 0.375 ohm pulldown in a SOT-23 body of 6 pins. The UCC27511 drives one N-channel MOSFET from a supply of 4.5 V to 18 V, with separate source and sink paths that give 4 A peak source and 8 A peak sink current. Propagation delay is 13 ns typical, rise time is 9 ns and fall time is 7 ns. The two inputs are independent of the supply rail and tolerate 18 V, the output is held low while VDD is below its UVLO threshold, and the body is the 6 pin DBV SOT-23 or the 3 mm DRS package with a thermal pad.

Order code and package

Order codeUCC27511DBVR
Supply voltage, VDD4.5 V to 18 V
Peak source current4 A pulsed
Peak sink current8 A pulsed
Propagation delay13 ns typical
Rise and fall time9 ns and 7 ns typical
Input voltage range0 V to 18 V, independent of VDD
Package6 pin SOT-23, DBV body
Pin count6
DocumentSLUSAW9F, February 2012, revised November 2014

Electrical parameters that decide the application

VDD absolute maximum20 V
Output low absolute maximum-2 V to 20 V, repetitive pulses under 200 ns
Input absolute maximum-0.3 V to 20 V
VDD UVLO at 25 C3.91 V rising, 4.20 V typical, 4.5 V maximum
VDD UVLO over temperature3.70 V to 4.65 V rising
Startup current at VDD 3.4 V25 uA typical, 75 uA typical, 145 uA maximum
Pulldown resistance0.375 ohm
Peak output current testminus 4 A source and plus 8 A sink into 0.22 uF at 1 kHz
Thermal resistance, DBV217.8 C per W junction to ambient
Thermal resistance, DRS85.6 C per W junction to ambient
Junction range-40 C to 140 C

Points to check before this part goes on a BOM

The 8 A sink figure is a transient number measured into a 0.22 uF load at 1 kHz, and the pulldown resistance of 0.375 ohm is what sets the real fall time. Into a gate with 40 nC of charge the sink current falls as the gate voltage falls, so the average current over the Miller plateau is what the driver actually delivers, not the peak. That is why the fall time of 7 ns is quoted at a stated load rather than as an unconditional figure.

The 4.5 V minimum supply is a hard floor and the UVLO window makes it harder. At 25 C the part releases somewhere between 3.91 V and 4.5 V, and over temperature the window widens to 3.70 V to 4.65 V, so a 5 V rail at minus five percent (4.75 V) is only 100 mV above the worst case release point and a 3.3 V logic rail cannot power the part at all. Boards that want to run from 3.3 V have to use a driver whose UVLO is specified below that rail.

The inputs are independent of the supply, which is the feature that saves a level shifter. A 3.3 V controller can drive IN+ and IN- directly while VDD sits at 12 V, and the inputs tolerate 18 V even with VDD at 4.5 V. The datasheet also notes that the maximum input voltage is not restricted by the VDD pin, so a fault that pulls the input above the rail does not forward bias anything inside the part.

Two supply current figures matter at different times. The startup current of 25 uA to 145 uA at 3.4 V is what a bootstrap resistor or a trickle supply has to deliver before the part releases, and it is the number that decides how long a high side bias takes to come up. Once running, the current is set by the gate charge and the switching frequency rather than by the quiescent draw.

Dissipation is small but not zero. Driving 60 nC at 12 V and 200 kHz is 0.144 W of gate charge loss inside the driver plus the loss in the internal pull up, and with 217.8 C per W for the SOT-23 body that is about 31 C of rise. The DRS package with its thermal pad cuts that to 85.6 C per W, which is why high frequency stages move to it rather than staying in the SOT-23.

The 0.375 ohm pulldown is the specification that keeps a MOSFET off when the driver is unpowered or its input floats. A bipolar totem pole stage would leave the gate undriven in that state and the switch could turn on through Miller coupling, so the resistive pulldown is a safety feature as much as a speed one. It also means the off state holds the gate low down to zero volts on VDD, which matters during a supply brownout.

Ordering the DBVR suffix fixes the SOT-23 body and the reel. The same die is available in the DRS package with the exposed pad, and the two are not footprint compatible, so a line that changes package needs a stencil change and a reflow profile check. The temperature range is -40 C to 140 C junction, which is wider than the 125 C of many comparable drivers and is part of why the part is used in motor drives.

Where this order code fits

This order code drives the main switch in switching supplies, synchronous rectifiers, motor phases and Class D output stages where a controller with a weak output has to charge 20 nC to 100 nC of gate charge in a few nanoseconds. The split source and sink current is what makes it useful in a synchronous buck, because the turn off path is the one that has to win the shoot through race. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the driver run from 3.3 V? No. The recommended minimum supply is 4.5 V and the UVLO release can be as high as 4.65 V over temperature. Use a driver rated below 3.3 V instead.

What sets the turn off speed? The 8 A sink path and the 0.375 ohm pulldown working against the gate charge. The 7 ns fall time is quoted at a stated capacitive load, so a larger gate takes longer.

Are the inputs 3.3 V logic compatible? Yes. The inputs are independent of VDD and accept 0 V to 18 V, so a 3.3 V controller drives them directly while VDD is at 12 V.

SUPERB holds this order code with date codes, packing and country of origin on the offer, and the Pin to Pin Cross Reference page lists the fields to compare before a gate driver position is filled from another line.