TPS77715DR
Product Specifications
TPS77715DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS77715DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS77715DR 750 mA 1.5 V regulator with reset in the SOIC body
The TPS77715DR is the 1.5 V fixed member of the TPS777 family in the eight pin SOIC body, ordered on a 2500 piece reel. It sources 750 mA with 260 mV of typical dropout on the 3.3 V member of the family, holds 2 per cent over the specified conditions and carries an open drain reset output with a 200 millisecond delay. Quiescent current is 85 microamp typical across the load range, and the loop is stable with a 10 microfarad low ESR output capacitor, which is the value the transient response is quoted against.
At 750 mA the thermal question comes before anything else. From 3.3 V to 1.5 V at full load the part turns 1.35 W into heat, which the eight pin body holds only with a copper pour under and beside the package; the same current from 2.5 V is 750 mW and comfortable. Current limit is 1.2 A to 1.7 A typical with 2 A at the top of the band, so the part survives the inrush of a large ceramic bank, and thermal shutdown at 150 degrees junction protects it if the copper is not enough.
Key parameters printed in the SLVS230G document
| Output | 1.5 V fixed, with fixed members at 1.5 V, 1.8 V, 2.5 V and 3.3 V plus an adjustable member |
| Load current | 750 mA |
| Dropout | 260 mV typical at 750 mA on the 3.3 V member of the family |
| Accuracy | 2 per cent over the specified conditions for fixed members |
| Quiescent current | 85 microamp typical across the load range |
| Current limit | 1.2 A typical, 1.7 A nominal, 2 A at the top of the band |
| Rejection and noise | 60 dB at 1 kHz with a 10 microfarad output capacitor, 54 microvolt RMS over 100 Hz to 100 kHz |
| Reset | Open drain, 200 millisecond delay, trip at 92 to 98 per cent of output, thermal shutdown at 150 degrees |
Package, reel and top side marking
| Package | SOIC, D body, eight pins |
| Reel | 2500 pieces on a large tape and reel for the DR row, 75 pieces in a tube for the plain D row |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 125 degrees, top side marking 77715 |
Where 750 mA is the right amount of margin
This rail is the one that feeds a memory bank or a motor driver logic supply, where the current is above half an amp and the load steps are abrupt. The fast transient response the family is named for comes from the loop compensation, which is why the output capacitor value is part of the specification rather than a suggestion. The reset output gives a controller a clean release, and because the comparator stays valid down to 1.1 V of input, a brown out holds the processor in reset instead of letting it run through a supply that is on its way down.
The practical decision between this member and the 500 mA family beside it is margin. A 750 mA part on a 600 mA load runs cooler at the same copper area and leaves room for a load that grows in a later build, which is usually cheaper than a board revision. The decision against it is dissipation from a 5 V input, where 750 mA into 1.5 V is 2.6 W and no eight pin body will hold that in still air; the power management cross reference page lists the switching alternatives for that case, and the how to verify a drop-in replacement page covers the measurements that separate two parts with the same pin out.
Questions buyers ask before ordering
Can it deliver 750 mA from a 5 V input? It can deliver the current, but 2.6 W in the eight pin body is beyond what the package holds in still air, so the copper area or a switcher in front is the answer.
Is the reset delay the same as the TPS775? Yes, 200 milliseconds internal, with the same 92 to 98 per cent trip point. The families differ in current rating, not in reset behaviour.
What is the noise figure? 54 microvolt RMS over 100 Hz to 100 kHz with a 10 microfarad output capacitor, which is low enough for a memory rail and not low enough for a precision reference without extra filtering.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line, confirms the reel and the moisture level, and keeps the date code with the certificate. Send the rail, the load and the input bus through the date code management page and the answer comes back with the reel size and the code that matches the drawing.