Contact Us

TPS77101DGKR

Brand: Texas Instruments
Texas Instruments TPS77101DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS77101DGKR — Power Management & Signal Chain | Superb Automation

TPS77101DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS77101DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS77101DGKR: adjustable 150 mA regulator with reset and a fixed 220 ms delay in an 8 pin MSOP body

TPS77101DGKR is an adjustable low dropout regulator with a built in reset generator, so a processor rail and its reset release come from one 8 pin part in a VSSOP body of 8 pins. It runs from 2.7 V to 10 V, sets any output between 1.5 V and 5.5 V from a 1.1834 V reference, and supplies 150 mA with 115 mV of dropout on the 3.3 V member. The reset output is open drain and holds for 220 ms after the rail is valid, with no external capacitor. Quiescent current is 92 uA typical and 125 uA maximum, which is high by modern standards and is the trade for the integrated reset.

Order code and package

TPS77101DGKR8 pin VSSOP (DGK), 80 pieces in a tube for the DGK string and 2500 pieces on a large reel for the DGKR string, nickel palladium gold finish, moisture level 1 unlimited, marking AFO, minus 40 C to plus 125 C
TPS77101DGKthe tube row of the same die, 80 pieces, which is the quantity a repair line actually wants
Fixed membersTPS77115, 118, 133 and 150 on the same body, with 1.5 V, 1.8 V, 3.3 V and 5.0 V outputs and a sense pin in place of the feedback pin
TPS772xxthe same silicon with a power good output instead of a reset output, and a 79 to 85 per cent trip point rather than a reset threshold
Obsolete codesthe document header names TPS77127, TPS77201, TPS77215 and TPS77218 as obsolete, so a BOM that calls for one of those has no current source
Second row per codethe addendum repeats each string with an .A suffix, and the .A row is the one that carries the published moisture level and finish

Electrical parameters that decide the application

Input voltage2.7 V to 10 V operating, 13.5 V absolute maximum, and the input must also be at least the output plus 1 V for the electrical table conditions
Output voltage1.5 V to 5.5 V adjustable, set by two resistors from the 1.1834 V reference, with 2 per cent tolerance on the fixed members
Output current150 mA continuous, with a 400 mA peak rating for 2 ms pulses at 50 per cent duty
Dropout voltage115 mV typical and 200 mV maximum at 150 mA on the 3.3 V member, 150 mV and 265 mV on the 2.8 V member, 75 mV and 115 mV on the 5.0 V member
Quiescent current92 uA typical and 125 uA maximum, which is the ground current at 1 mA of output
Current limit0.9 A minimum and 1.3 A maximum with the output pulled to ground
Reset delay220 ms fixed, generated internally, with no external capacitor and no way to change it
Reset thresholdthe reset output is valid from 1.1 V of input, and the trip point is specified as a percentage of the output rather than as a fixed voltage
Noise55 microvolt rms over 300 Hz to 100 kHz on the 1.8 V member without a bypass capacitor
Ripple rejection55 dB at 1 kHz on the 1.8 V member
Thermal shutdown144 C junction typical, which is lower than the 150 C class parts around it
Output capacitor10 uF is the value used for the electrical table, and the part is stable with low ESR ceramic as well as with a 1 uF tantalum

Reset or power good, and which voltage

TPS771xxreset output, open drain, active low, held for 220 ms after both the input and the output are above their thresholds
TPS772xxpower good output, open drain, active high, tripping at 79 to 85 per cent of the output with 0.5 per cent of hysteresis
Adjustable memberTPS77101 uses pin 1 as a feedback input and needs the divider. The fixed members use pin 1 as a sense input tied to the output
1.8 V memberTPS77118, the one whose 55 microvolt noise and 55 dB rejection figures are quoted in the table
Obsolete membersTPS77127, TPS77201, TPS77215 and TPS77218 are named obsolete in the header, so those BOM lines need a replacement rather than a reorder
MSOP body8 pins, 3 mm by 3 mm, which is the same footprint the TPS772xx uses, so a reset to power good change does not move the land pattern

Points to check before this part goes on a BOM

The reset delay is 220 ms and it is fixed. There is no capacitor to change, which removes a component and a tolerance from the BOM and also removes the ability to tune the delay to a processor that needs a longer hold. A board that needs 400 ms has to add an external supervisor or accept a 220 ms release. That trade is the whole point of the part, and it is also the reason it does not fit every processor family.

Quiescent current of 92 uA typical and 125 uA maximum is two orders of magnitude above what a modern low dropout regulator draws, and that is the price of the integrated reset and the 2000 era process. A battery product that keeps this regulator alive in standby loses about 1 mAh a day to it. The part belongs on a line powered or a mains charged board, and on a battery board it belongs behind a load switch rather than on the always on rail.

The 200 mV maximum dropout at 150 mA belongs to the 3.3 V member, and the numbers move with the output voltage. The 2.8 V member is specified at 265 mV maximum and the 5.0 V member at 115 mV, because dropout scales with the pass device rather than with the load alone. An adjustable member set to 1.5 V is not covered by any of those rows, so its dropout has to be taken from the curve rather than from the table.

The current limit window of 0.9 A to 1.3 A on a 150 mA part is unusually wide. It protects the pass device and the package, not the load. A short circuit draws at least 0.9 A, which is six times the rated current and enough to drop the input rail on a weak source before the thermal shutdown at 144 C reacts. The 400 mA peak rating for 2 ms pulses is the only sanctioned way to exceed 150 mA, and it assumes a 50 per cent duty cycle, so a load that pulls 300 mA continuously is outside the specification even though the current limit will not stop it.

The reset and power good outputs are not the same function and the trip points are not the same percentage. The reset output is tied to the regulator's own threshold and releases 220 ms after the rail is valid. The power good output trips at 79 to 85 per cent of the output with 0.5 per cent of hysteresis, which is a monitor rather than a reset. Swapping TPS771xx for TPS772xx on the same footprint changes the polarity and the threshold, and a board that treats them as drop in equivalents will hold a processor in reset forever or release it far too early.

The document names four obsolete codes in its own header. That is unusual and useful: TPS77127, TPS77201, TPS77215 and TPS77218 have no current source, and a BOM that lists one of them cannot be filled from new stock whatever the distributor catalogue says. The remaining members, including the adjustable 101 string on this page, are still active in the addendum, which is why the 101 is the code to standardise on when only the adjustable function is needed.

The 10 V input ceiling is the constraint that decides whether this part fits. A 12 V rail cannot feed it directly even though the absolute maximum is 13.5 V, because the recommended operating range stops at 10 V. A board that runs from a 12 V bus needs a regulator rated for the bus, and this family is for 5 V and 9 V systems. That single number eliminates more candidate applications than any other figure in the table.

Where this order code fits

It sits on 5 V and 9 V processor boards in industrial controllers, portable instruments and telecom line cards, where a small processor rail needs its reset release generated inside the regulator footprint. Teams comparing it with a neighbouring part start from our Obsolete Part Cross Reference Hub page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the 220 ms reset delay be changed? No. It is generated internally and there is no capacitor pin. A board that needs a different delay has to add an external supervisor.

What is the difference between TPS771 and TPS772? TPS771 has an active low reset output released 220 ms after the rail is valid. TPS772 has an active high power good output that trips at 79 to 85 per cent of the output.

Is this part suitable for a battery product? Only behind a load switch. The 92 uA typical and 125 uA maximum quiescent current would drain a small cell in weeks if left on continuously.

How much headroom does the 3.3 V member need? 3.5 V at 150 mA across temperature, because the maximum dropout on that member is 200 mV. The 2.8 V member needs 265 mV.

Which codes are obsolete? TPS77127, TPS77201, TPS77215 and TPS77218 are named obsolete in the document header. The adjustable 101 string on this page is still active.

Does it work from a 12 V rail? No. The recommended input range stops at 10 V, and the 13.5 V absolute maximum is a damage limit rather than an operating range.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Power Management Cross Reference page sets out the checks that keep a substitute from failing on the bench.