Contact Us

TPS73601DCQR

Brand: Texas Instruments
Texas Instruments TPS73601DCQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73601DCQR — Power Management & Signal Chain | Superb Automation

TPS73601DCQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73601DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73601DCQR: 400 mA adjustable low dropout regulator that is stable with no output capacitor

TPS73601DCQR is an NMOS low dropout regulator in a voltage follower arrangement, which is what lets it run without an output capacitor and keep its ground current flat across the load range in a SOT-223 (DCQ) body of 6 pins. It takes 1.7 V to 5.5 V in, delivers 400 mA with 75 mV of dropout typical and 200 mV maximum at full load, holds the adjustable output against a 1.204 V reference to 0.5 per cent at room temperature and 1 per cent over line, load and temperature, and quotes 30 uV RMS of output noise with a 0.1 uF noise reduction capacitor.

Order code and package

Ordering stringTPS73601DCQR, the six pin SOT-223 body on a 2500 piece large reel
Part markingPJFQ on the body
BodySix pin SOT-223, 6.50 mm by 7.06 mm, with the tab acting as the heat path
Other bodies in the familyFive pin SOT-23 measuring 2.90 mm by 2.80 mm, and eight pin VSON measuring 3.00 mm by 3.00 mm
Addendum noteThe vendor table prints the .A row of this string against the eight pin SON body, so the body has to be named on the purchase order and not only the string
Voltage optionsFixed outputs from 1.20 V to 5.0 V plus the adjustable member on this page, which sets its output from 1.20 V to 5.5 V with an external divider
Temperatureminus 40 to 125 degrees junction

Electrical parameters that decide the application

Input range1.7 V to 5.5 V, which rules out a 12 V rail and puts the part on a low voltage bus or directly after a converter
Output current400 mA, with the current limit window at 500 to 800 mA on current silicon and 400 to 650 mA on the earlier one
Dropout75 mV typical and 200 mV maximum at 400 mA, quoted with the input at nominal output minus 0.1 V
Reference1.204 V typical, 1.198 to 1.210 V at 25 degrees, which sets the adjustable output level
Accuracy0.5 per cent initial, 1 per cent over line, load and temperature, on outputs from 1.2 V to 5.5 V
Noise30 uV RMS from 10 Hz to 100 kHz with a 0.1 uF noise reduction capacitor fitted
Ground current400 uA typical and 550 uA maximum at 10 mA, 630 uA maximum at 400 mA, which is nearly flat because the pass device is a follower rather than a common source stage
Shutdown currentUnder 1 uA with the enable low
Line regulation0.01 per cent per volt, load regulation 0.0005 per cent per milliamp
Output impedance in dropout0.25 ohm typical, 800 milliohm maximum, which sets how the rail sags when the input falls below the regulated level
Short circuit450 mA of short circuit current with the output pulled to zero, protected by a foldback limit
Reverse leakage0.1 uA typical and 10 uA maximum with the enable low and the output above the input
Output capacitorOptional. The part is stable with none, with ceramic, or with any value and type, which is the unusual claim in this class

Family variants and how they differ

Fixed against adjustableThe fixed members have the divider inside the package and three pins in use, while this member brings the feedback pin out. The adjustable version is the one used when the rail has to be trimmed or set to a value the fixed list does not cover
Two silicon generationsThe current limit window differs between the earlier and the current silicon, 400 to 650 mA against 500 to 800 mA, and the ground current rows are quoted separately for each. A board qualified on one generation is not automatically identical on the other
BodiesThe SOT-223 tab is the thermal path and gives the lowest junction to ambient figure of the three. The SOT-23 body is the smallest and the VSON sits between them with the pad underneath
Reverse current protectionThe NMOS follower blocks current from output back to input when the enable is low, with leakage in the sub microamp range. That matters on a rail that is held up by a charged load after the input is removed
Noise reduction pinThe external capacitor on the NR pin filters the reference, and the 30 uV RMS figure assumes 0.1 uF. Without it the noise is higher, which is the first thing to check when a part is substituted into a low noise rail
No thermal shutdown lockoutThe part has thermal shutdown, but it is a protection and not a regulation feature. A board that runs the part at 400 mA from 5 V into 1.8 V dissipates 1.28 W and needs the tab soldered to copper

Points to check before this part goes on a BOM

The part is stable with no output capacitor, which is not the same as being at its best that way. A 0.1 uF or larger capacitor at the load still improves the transient response, and the data sheet shows both cases rather than claiming one is unnecessary.

The 5.5 V input ceiling is the hard limit on where this part can sit. A rail that comes from a 12 V bus needs a converter in front of it, and the dropout figure then has to be read against the converter's output tolerance rather than against the bus.

Ground current is nearly flat across the load range because the pass device is an NMOS follower fed by an internal charge pump. That is an advantage on a battery rail, and it also means the quiescent current does not fall away at light load the way a bipolar regulator's does.

Reverse current is blocked while the enable is low, but the leakage is quoted at up to 10 uA. On a rail that has to hold charge for hours after the input is removed, that leakage is part of the hold time calculation.

The current limit window is 500 to 800 mA on current silicon. A load that draws 700 mA in a fault will be limited on one part and not on another, so the limit is a protection threshold rather than a specified current.

At 400 mA from 5 V into 1.8 V the part dissipates 1.28 W. In the SOT-223 body that is a copper area question, not a silicon question, and a board that mounts it on a thin trace will reach thermal shutdown at full load.

Why a regulator with no output capacitor is useful

Most low dropout regulators need a capacitor at the output to keep their loop stable, and the capacitor has to be a type and value the vendor has characterised. In a radio front end that capacitor is often the largest part on the rail and the one that couples noise into the sensitive node it was meant to protect.

An NMOS pass device in a voltage follower arrangement has a different loop behaviour, and the TPS736 is stable with nothing at the output. That does not remove the need for decoupling at the load, but it removes the requirement that the regulator itself be compensated by a capacitor, which is the part that usually constrains the board.

Where this order code fits

Supply rails for voltage controlled oscillators and phase locked loops, post regulation of a switching rail where the switching ripple has to be removed, point of load supplies for DSP, FPGA and ASIC cores, and portable instruments where board area rules out a large output capacitor. The noise figure and the flat ground current are the two reasons this part shows up in radio and converter front ends rather than a general purpose regulator. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Can it run with no capacitor at the output? Yes. The part is specified stable with no output capacitor and with any value or type, which is unusual for a low dropout regulator and is the reason it is used where the output capacitor would be the largest part on the rail.

What is the dropout at full load? 75 mV typical and 200 mV maximum at 400 mA. A 1.8 V rail therefore needs at least 2.0 V at the input to stay in regulation over the full tolerance range.

How is the output set on this member? With an external divider into the 1.204 V feedback pin. The divider tolerance adds to the 0.5 per cent initial accuracy, so a one per cent resistor pair gives a rail closer to two per cent.

Is the noise figure available without the noise reduction capacitor? No, the 30 uV RMS figure is quoted with 0.1 uF on the noise reduction pin. Without that capacitor the reference noise passes through to the output.

What happens if the output is shorted? The foldback limit holds the short circuit current at 450 mA and the thermal shutdown protects the die. The part recovers when the fault is removed rather than latching off.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.