Contact Us

TPS70930DBVR

Brand: Texas Instruments
Texas Instruments TPS70930DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS70930DBVR — Power Management & Signal Chain | Superb Automation

TPS70930DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS70930DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS70930DBVR: a 3.0 V 150 mA regulator that takes 30 V of input and draws 1 microamp

TPS70930DBVR is a fixed 3.0 V linear regulator for a rail that sits on a high voltage line and has to keep its sleep current in the microamp range in a SOT-23 (DBV) body of 5 pins. The input window is 2.7 V to 30 V, the output is fixed at 3.0 V with 2 per cent accuracy over temperature, and the continuous current is 150 mA with a 200 mA peak. Quiescent current is 1 microamp and the shutdown current is 150 nA, reverse current protection stops the output from feeding a collapsed input, and current limit with thermal shutdown protects the pass element. The 3.0 V output is the one that a 3 V logic or a 3 V sensor bridge needs, and the body is the 5 pin SOT-23.

Order code and package

TPS70930DBVRthe 3.0 V member in the 5 pin SOT-23 body, a 3000 piece large reel row with marking SID on the .A and .B lines and a 250 piece small reel row on the plain line, so the packing is quoted on the offer
TPS70933 and TPS70936the 3.3 V and 3.6 V members, same rating and same body, which are the strings a 3.3 V logic rail orders
TPS70939the 3.9 V member, which is the one used when the rail has to stay above a 3.6 V threshold on a 4 cell alkaline pack
Adjustable membersthe same family with a feedback pin and a 1.2 V reference, for a rail between the fixed steps
WSON-6 bodythe second body, 2.0 mm by 2.0 mm, with the same electrical table and a better thermal path
Enable pinactive high on the SOT-23 body, with the part in shutdown at 150 nA when the pin is pulled low

Electrical parameters that decide the application

Input voltage2.7 V to 30 V recommended, with the absolute maximum above that, so a 12 V or 24 V industrial line is inside the window
Output voltage3.0 V fixed on this code, from a family table of 1.2 V to 6.5 V
Output current150 mA continuous and 200 mA peak, so a burst load is covered by the peak figure and the average has to stay under the continuous one
Quiescent current1 microamp typical into the ground pin at no load, which is the figure a battery budget uses
Shutdown current150 nA typical with the enable low
Accuracy2 per cent over line, load and temperature, which is a logic rail figure rather than a reference figure
Dropout voltagea few hundred millivolts at 150 mA on the 3.0 V member, so a 3.3 V bus holds the rail at full load and a 3.6 V pack holds it for most of its curve
Reverse current protectionthe pass element blocks current from output to input while the part is disabled, which protects the part when a rail is back driven
Current limitan internal limit protects the pass element during a fault, and the output recovers when the fault clears
Thermal shutdownjunction overtemperature turns the pass element off, which is what protects a 5 pin body at 150 mA
Enable pinactive high, part regulating above the threshold and drawing 150 nA when it is held low
Temperatureminus 40 C to 125 C junction over the electrical table

Voltage steps around this member

TPS70930DBVRthis order code, 3.0 V fixed in the 5 pin SOT-23, with a 3000 piece large reel row and a 250 piece small reel row under the same base string
TPS70933 and TPS70936the 3.3 V and 3.6 V members, same rating and same body, chosen by what the load is specified down to
TPS70939the 3.9 V member, used where the rail has to stay above a 3.6 V threshold on a 4 cell alkaline pack
Adjustable membersthe same family with a feedback pin, for a rail between the fixed steps
Input window2.7 V to 30 V, so a 12 V or 24 V line is inside the same part as a 3.3 V bus
Sleep current1 microamp typical and 150 nA in shutdown, which is what a loop powered instrument needs
Dissipation24 V in and 3.0 V out costs 21 mW per milliamp, so the high input case runs at low current in bursts

Points to check before this part goes on a BOM

A 3.0 V rail is usually a battery end of life decision. A 3.0 V logic rail on a 3.3 V bus has 300 mV of headroom, which is inside the dropout at full load. The rail only holds while the load stays under about 100 mA, and a product that needs the full 150 mA has to come from a higher bus or accept a lower rail.

The high input voltage is the reason to choose this family over a 6 V part. On a 12 V or 24 V line the alternative is a switching stage plus a linear regulator, and at 150 mA the switching stage costs more area and more noise than the headroom it saves. The cost is dissipation, which the thermal section of the document addresses rather than hides.

1 microamp is measured with no load. Ground current rises with load current, and the sum is what the battery sees. A product that quotes 1 microamp and then draws 60 mA is quoting the wrong line, and the arithmetic that matters is the average over the duty cycle.

3.0 V is not 3.3 V with a different label. A 3.3 V logic device specified to 3.0 V minimum has no margin on a 3.0 V rail once tolerance and ripple are included. The 3.0 V member of this family exists for devices that are specified down to 2.7 V, and the data sheet of the load decides which member is bought.

The SOT-23 thermal limit arrives before the current limit. 150 mA at 24 V of input is 3.15 W in a 5 pin body, which it cannot dissipate. The real operating point at high input is a low output current, and the same part at 5 V of input can run at the full 150 mA.

Reverse protection is not reverse polarity protection. The part survives an output that is held above the input while it is disabled. A reversed battery still destroys it, and that case needs a series device in front.

A 3.0 V sensor rail on a 24 V loop supply

A 4 to 20 mA loop transmitter, an industrial sensor or a field instrument often has a 24 V line and needs a 3.0 V rail for a bridge and a microcontroller. The regulator has to hold that rail while drawing almost nothing between measurements, because the loop current budget is fixed. A part with 1 microamp of quiescent current leaves the rest of the 4 mA for the electronics, and a part with 50 microamps does not.

The dissipation is the other half of the decision. At 24 V in and 3.0 V out, every milliamp of load costs 21 mW, so a 20 mA load is 420 mW in a 5 pin body. On those products the regulator runs at a low current and the heavy work is done in bursts, which is exactly the pattern the peak rating covers.

Telling the 3.0 V and 3.3 V members apart on a purchase order

The two strings differ by one digit and share a data sheet, a body and a reel size. A board built with the wrong one still powers up, and the failure appears later as a device that resets under load or an ADC that reads low. The offer should name the output voltage explicitly rather than only the ordering string, which is the check that catches a picking error before the parts reach the line.

Where this order code fits

a 3.0 V sensor or logic rail on a 12 V or 24 V industrial line, an instrument on a loop supply, or a standby rail that has to hold its sleep current over years Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What input range does it accept? 2.7 V to 30 V, so a 12 V or 24 V line is inside the window and a 3.3 V bus is at the bottom of it.

Can it deliver 150 mA from a 3.3 V bus? Only while the headroom stays above the dropout, which at 150 mA it does not. On a 3.3 V bus the usable current is lower, and the curve in the document gives the figure for the output voltage.

How much current does it draw when the load is off? 1 microamp typical, with 150 nA in shutdown when the enable pin is low.

What is the difference from the 3.3 V member? The output voltage only. Same body, same reel, same table, one digit in the part number, which is why the offer should state the voltage rather than only the code.

Does it need an output capacitor? Yes, a ceramic output capacitor is required for stability, and the data sheet gives the range that keeps the loop stable over temperature.

What does SUPERB put on the offer for this line? The exact ordering string, the output voltage, the reel quantity, the date code and the country of origin, because the same body carries a 3.0 V and a 3.3 V die under strings that differ by one digit.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.