TPS6521905RSMR
Product Specifications
TPS6521905RSMR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS6521905RSMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS6521905RSMR user programmable PMIC with three converters and four LDOs
The TPS6521905RSMR is a user programmable power management IC built around three step down converters and four linear regulators, with the default voltages, the power up sequence and the pin functions held in non volatile memory. The converter set is one 3.5 A rail and two 2 A rails, all from a 2.5 V to 5.5 V input with an output range of 0.6 V to 3.4 V and dynamic voltage scaling on all three. The body is a 32 pin QFN offered in 4 mm by 4 mm and 5 mm by 5 mm versions.
The four LDOs split into two pairs. Two deliver 400 mA from a 1.5 V to 5.5 V input over 0.6 V to 3.4 V and can be configured as load switches or in bypass mode, which is what an SD card slot needs because the card rail has to follow the host rail rather than regulate above it. The other two deliver 300 mA from 2.2 V to 5.5 V over 1.2 V to 3.3 V, also with a load switch mode.
Switching frequency reaches 2.3 MHz, which keeps the inductors at 470 nH and the input capacitance at 4.7 microfarads, with a minimum of 10 microfarads of output capacitance per rail depending on the mode the converters are set to. An I2C interface plus configurable multi function pins carry the control to the host.
Key parameters from the SLVSGZ4A document
| Converter 1 | 2.5 V to 5.5 V input, 3.5 A, 0.6 V to 3.4 V output, dynamic voltage scaling |
| Converters 2 and 3 | 2.5 V to 5.5 V input, 2 A each, 0.6 V to 3.4 V output, dynamic voltage scaling |
| LDOs 1 and 2 | 1.5 V to 5.5 V input, 400 mA, 0.6 V to 3.4 V, bypass and load switch modes |
| LDOs 3 and 4 | 2.2 V to 5.5 V input, 300 mA, 1.2 V to 3.3 V, load switch mode |
| Switching frequency | Up to 2.3 MHz, power save and forced PWM modes |
| Passives | 470 nH inductor, 4.7 microfarad input capacitor, 10 microfarad minimum output per rail |
| Input limit | 2.5 V to 5.5 V on VSYS, 6 V absolute maximum, 200 mV of allowed excess on a converter input pin |
| Sequencing | Programmable power up and power down order, defaults held in NVM |
| Interface | I2C in standard, fast and fast plus modes, GPIO and multi function pins |
| Package | 32 pin QFN in 4 mm by 4 mm and 5 mm by 5 mm, moisture level 2 |
What programmable buys and what it costs
A board built around this part can be revised by changing one NVM image rather than by changing the bill of materials: a rail that moves from 1.2 V to 1.8 V, a sequence that has to swap two positions, a GPIO that changes polarity. That is worth real money on a product family with several variants, because the same reel feeds all of them.
The cost is in the release process. The NVM settings have to be captured in a file that belongs to the product, checked against the rail list, and re checked whenever a new image is ordered. A part ordered with the wrong image regulates correctly but comes up in the wrong order, which is the failure that survives bench bring up and appears in the field as a latch up on a fraction of units.
Where this part fits
Industrial controllers, portable instruments, single board computers and any product that needs three converters plus four quiet rails with a defined sequence from a 3.3 V or 5 V supply. The cross reference notes for this family sit under power management cross reference and the shortage route under BOM shortage recovery.
What to check before a purchase order
Check the NVM image against the product, not against the family name. The order code carries the image and the addendum does not decode it in words, so the image has to come from the vendor configuration file or from the previous purchase record. A reel bought by family name alone lands on whatever image the distributor stocks.
Check the LDO configuration pins as well. A rail set to bypass mode follows the input and cannot regulate, which is correct for an SD card slot and wrong for an analogue rail. The receipt check on a programmable part is in date code management.
Questions that come up on this part
Can the sequence be changed in the field? Only by reprogramming the NVM, which the vendor supports through the bus in the initialize state, and a mistake there takes effect immediately rather than at the next power cycle.
Is a 400 mA LDO enough for an SD card? For the card rail in bypass mode the current comes from the host rail, so the 400 mA figure applies to the switch, not to the card's peak write current.