TPS650842A0RSKR
Product Specifications
TPS650842A0RSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS650842A0RSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS650842A0RSKR: six rail PMIC for Intel Braswell class platforms
TPS650842A0RSKR is a single chip power management IC that generates the full rail set for a 2, 3 or 4 cell battery platform in a VQFN (RSK) body of 64 pins. It carries three step down controllers that drive external FETs, three integrated step down converters, a sink and source VTT rail for DDR memory, three LDOs and three load switches, all sequenced by an internal power up state machine and steered over I2C at address 0x5E.
Order code and package
| Order code read out | TPS650842 A0 RSK R: family TPS650842, A0 factory OTP image, RSK 64 pin VQFN, R large tape and reel |
| Package | VQFN (RSK), 64 pins, 8.00 mm by 8.00 mm, thermal pad on the underside |
| Carrier in the vendor addendum | TPS650842A0RSKT, 250 piece small reel, is the only row published on 21 April 2026; a 2000 piece RSKR reel is not in that table and should be confirmed on the purchase order |
| Operating temperature | minus 40 to plus 85 degrees Celsius, industrial and commercial grade, not an automotive grade |
| Moisture and finish | MSL level 3, 260 degrees peak reflow, 168 hour floor life, NIPDAU lead finish |
| Control interface | I2C at 0x5E, standard mode 100 kHz, fast mode 400 kHz and fast mode plus 1 MHz |
| Marking | T650842A0 with the PG1.0 process code |
Electrical parameters that decide the application
| Controller input, BUCK1, BUCK2 and BUCK6 | 5.6 V to 21 V, the wide rail fed straight from the battery or the 12 V adapter |
| Converter input, BUCK3, BUCK4 and BUCK5 | 4.5 V to 5.5 V, taken from the 5 V system rail |
| BUCK1 VCC and BUCK6 VDDQ | up to 7 A each with external FETs, controller capability only, the real figure follows the FETs and inductor chosen |
| BUCK2 VGG | up to 11 A with external FETs, D-CAP2 control |
| BUCK3 VNN | up to 3.5 A integrated, I2C DVS from 0.65 V to 1.45 V in 25 mV steps |
| BUCK4 V1P05A and BUCK5 V1P8A | 3 A and 1.5 A integrated, DCS-Control |
| BUCK6 VDDQ | 1.2 V or 1.35 V selected by a pin, which is what maps the part to DDR4 or DDR3L memory |
| DVS on BUCK1 to BUCK3 | 0.5 V to 1.45 V in 10 mV steps, which is the Connected Standby requirement |
| LDOA1 | 1.35 V to 3.3 V, 200 mA, voltage selected over I2C |
| LDOA2 and LDOA3 | 1.05 V, 1.1 V, 1.15 V or 1.2 V on LDOA2 and 1.1 V, 1.15 V, 1.2 V or 1.24 V on LDOA3 |
| Load switches | 300 mA each, drop below 1.5 percent of nominal input voltage, on resistance under 96 milliohm at a 1.8 V input |
| VTT rail | sinks and sources, tracks the VDDQ setting for memory termination |
| Load switch slew rate | controlled ramp, so a card slot or a radio module does not see a current step at enable |
| BUCK4 and BUCK5 control | DCS-Control, which is a hysteretic style loop that keeps the transient response fast without external compensation |
Family variants and how they differ
| TPS650842 | the part on this page, tuned to the Braswell rail map with BUCK1 at 7 A and BUCK2 at 11 A |
| TPS65094 family | the Apollo Lake sibling, TPS650940 through TPS650947, with different current splits and an OTP programmed VDDQ default |
| A0 image | the factory default image, which fixes start up voltages, rail order and the DVS tables |
| Other images | a different letter or digit changes the default rail set, so the letter is part of the part number and not a revision marker |
| Document class | SWCS132 is the public summary, the full electrical tables are released on request through the vendor mailbox printed on page one |
Points to check before this part goes on a BOM
The public document is a summary, not the full data sheet. It runs to a few pages of features, a pin list and an application diagram, and it ends by telling the reader to request the full version by email. Every timing number, every FET recommendation and every register map sits in that fuller document, so a platform bring up should not be planned from the public file alone.
The A0 block is a factory programmed image, not an accuracy grade. Start up order, default output voltages and the DVS step tables are burned into that image, so a TPS650842 with a different suffix opens at different rails even though the die is the same. A second source offer has to name the full string, and a customer who asks for a substitute should be asked which image their firmware expects.
The published reel is the small one. The vendor addendum dated 21 April 2026 lists TPS650842A0RSKT at 250 pieces on a small carrier. The R suffix on this order code means the large reel, which is the normal production packing, so a purchase order should state the reel size and let the offer confirm it rather than assume the catalogue row.
DDR termination rides on the VTT LDO and has to match the memory generation. BUCK6 sets VDDQ at 1.2 V for DDR4 or 1.35 V for DDR3L through a pin strap, and VTT follows that setting. A board built for DDR3L that is populated with DDR4 parts, or the reverse, will pass power up and then fail memory training, which is the expensive kind of failure because it appears after the boards are assembled.
The 7 A and 11 A figures belong to the controller, not to the board. BUCK1, BUCK2 and BUCK6 drive external FETs, so the current the rail can actually deliver is set by the FET pair, the inductor saturation current and the copper under them. A quote for this part is therefore a quote for the controller, and the thermal question stays with the platform.
Two of the six rails carry the platform state that is hardest to debug. BUCK4 and BUCK5 feed the 1.05 V and 1.8 V rails that stay alive in standby, and they use a hysteretic loop that reacts in a few switching cycles. When a board fails to resume from standby, the rail that sagged is usually one of these two, and the load step that caused it comes from a device waking up rather than from the processor.
Where this order code fits
These parts sit in fanless industrial PCs, thin clients, point of sale terminals and handheld instruments that run from a 2 to 4 cell pack or a 12 V adapter and need a memory rail, a standby rail and a battery charging path in one footprint. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.
Questions buyers ask
Can the TPS650842 replace a TPS65094 on an existing board? Only if the rail map matches. The pinout family is close but the current splits and the OTP defaults differ, and BUCK6 is pin strapped on the TPS650842 while the TPS65094 programs its VDDQ default. Check each rail against the platform rail map before treating the two as interchangeable.
Is this part still active? Yes. The vendor addendum lists TPS650842A0RSKT as active production with a PG1.0 process code, and the TPS65094 family that shares the footprint is also active. Long term availability is a separate question for a 2015 generation part, and a last time buy plan is worth holding.
What do you need to quote it? The full ordering string, the annual quantity, the reel size you want and the target date. We confirm the image letter against your firmware expectation and state date codes and country of origin on the offer.
How many rails does the part sequence? Six regulators, a VTT termination rail, three LDOs and three load switches, all driven by one power up state machine. The order is fixed by the OTP image rather than by external components.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.