Contact Us

TPS62A01DRLR

Brand: Texas Instruments
Texas Instruments TPS62A01DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62A01DRLR — Power Management & Signal Chain | Superb Automation

TPS62A01DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62A01DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62A01DRLR: 2.5 V to 5.5 V, 1 A synchronous buck in a six pin SOT-563

TPS62A01DRLR is a synchronous step down converter with both switches inside a 1.6 mm body and a 600 mV reference in a SOT-563 body of 6 pins. It takes a 5 V or 3.3 V rail down to a low voltage point of load without a diode, a sense resistor or a compensation network, and it holds full duty cycle when the input falls to the output.

Order code and package

Order codeTPS62A01DRLR, DRL package, SOT-563, six pins, 3000 pieces on a large reel
FamilyTPS62A01 at 1 A and TPS62A02 at 2 A, in DRL and DDC bodies with different switch resistances
BodySOT-563, 1.6 mm by 1.6 mm, six pins, no exposed pad
Switches180 mOhm high side and 120 mOhm low side in the 1 A DRL body
Reference0.6 V, 594 mV to 606 mV at 25 C and 591 mV to 609 mV over the full temperature range
Output range0.6 V to VIN, so the part passes the input through at 100 per cent duty rather than dropping out

Electrical parameters that decide the application

Input range2.5 V to 5.5 V operating, under voltage lockout at 2.3 V to 2.5 V rising and 2.2 V to 2.4 V falling
Output current1 A continuous in the DRL body, 2 A in the DDC and 2 A bodies
Switching frequency2.4 MHz nominal, which keeps the inductor small but limits the duty at high input
Quiescent current23 uA typical while regulating with no load, 0.01 uA in shutdown
Feedback accuracy1 per cent from 0 C to 125 C, which is the number to use rather than the 25 C window
Enable1.2 V rising and 0.4 V falling, with 100 nA of leakage so a high value divider can drive it
Conduction modePower save mode at light load on one option, forced PWM on the other, selected by the order code
ProtectionCycle by cycle current limit, thermal shutdown, and a soft start that ramps to the reference without overshoot

Family variants and how they differ

TPS62A022 A in the same family with 100 mOhm and 67 mOhm switches, for a load this part cannot reach
TPS62A01DDCRthe same 1 A die in a SOT-23-6 body, one body size larger with the same pin functions
TPS5622072 A from a 17 V input in a SOT-563, for a rail that comes from 12 V rather than 5 V
TPS62201a 300 mA fixed 1.8 V step down in SOT-23-5, for a load an order of magnitude smaller
TPS62872a 12 A converter with an I2C interface, for the core rail that this part only supplies at low current

Points to check before this part goes on a BOM

The 2.4 MHz switching frequency is the reason the inductor can be 1 uH and the output capacitor 10 uF, and it is also the reason the part cannot regulate a very low output from a 5 V input. At 5 V to 0.6 V the duty is 12 per cent, which is 50 ns of on time per cycle, and the minimum on time plus the gate delay eat a measurable part of that. A 5 V to 1.2 V rail at 25 per cent duty is the comfortable region for this part.

The 100 per cent duty mode is the feature that separates it from the generation before. When the input falls to the output the high side switch stays on and the part stops switching, so a 3.3 V rail fed from a 3.6 V source keeps regulating instead of collapsing at the first sign of a droop. The catch is that the output then sits at the input minus the resistive drop, and there is no switching to hide it, so the rail follows the source down as the load rises.

The reference is specified two ways and the tighter one is not the useful one. The 594 mV to 606 mV window is at 25 C, and the 591 mV to 609 mV window is over the full range from 0 C to 125 C. The 1 per cent accuracy claim belongs to the second window, so a board that needs 1.2 V within two per cent has 24 mV of total error and 9 mV of it already spent on the reference before the divider resistors contribute anything.

The 23 uA quiescent current only applies in power save mode. In forced PWM the part keeps switching at 2.4 MHz with no load and draws milliamps, which is the right trade for a rail that feeds an analog block or a radio, and the wrong trade for a battery node that sleeps. The order code decides which behaviour the board gets, so the choice has to be made when the BOM is released rather than when the board is laid out.

The enable pin draws 100 nA, which is low enough for a 1 Mohm divider to set an under voltage lockout without the pin current moving the trip point. The 1.2 V rising and 0.4 V falling thresholds are far apart on purpose: a rail that sags to 0.9 V during a load step does not restart the converter, and only a fall below 0.4 V is treated as a shutdown command.

The six pin body has no exposed pad, so the 1 A rating is a statement about the copper under the pins rather than about the die. At 5 V to 1.8 V and 1 A the conduction loss is 0.09 W in the high side and 0.05 W in the low side, and the switching loss at 2.4 MHz adds a similar amount, so the package sheds about a quarter of a watt through six leads. A board that pours 20 mm squared of copper on each of the four power pins is the one that gets the full amp.

The DRL and DDC bodies are not interchangeable even at the same current. The switches in the 1 A DDC and 2 A parts are 100 mOhm and 67 mOhm, against 180 mOhm and 120 mOhm in the 1 A DRL, so a substitution changes the loss and the thermal headroom. The pin functions are the same, which makes the swap look safe on a netlist and fail in a thermal test.

Soft start is internal and the ramp is monotonic, so a pre-biased output is not discharged when the part is enabled. That matters on a board where a second source holds the rail, and it also means the inrush into the output capacitor is set by the internal ramp rather than by a capacitor the board team can add. A 22 uF output charged by a 1 ms ramp is about 11 mA of charging current at 1.2 V, which is small against the 1 A rating.

Where this order code fits

It belongs on the 5 V or 3.3 V rail of a sensor board, a camera module, a wireless node or an industrial controller, where one rail between 0.6 V and the input has to carry up to an amp and the board has no space for a controller with external switches. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

What happens when the input falls below the set output? The part goes to 100 per cent duty and passes the input through minus the resistive drop. It does not switch, so there is no boost and the output follows the input down.

Is the 1 A rating available in the SOT-23 body? Yes, the DDC body carries the same 1 A with 100 mOhm and 67 mOhm switches, so it runs cooler than the SOT-563 version at the same load.

How much output voltage error should be budgeted? The reference alone is 591 mV to 609 mV over temperature, which is 1 per cent, and the divider resistors add to it. A two per cent window needs one per cent resistors.

Does it need an external compensation network? No. The loop is internally compensated and specified for ceramic output capacitors, so the BOM is the converter, one inductor and the capacitors.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.