Contact Us

TPS628302ARZER

Brand: Texas Instruments
Texas Instruments TPS628302ARZER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS628302ARZER — Power Management & Signal Chain | Superb Automation

TPS628302ARZER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS628302ARZER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS628302ARZER 2 A synchronous buck in the same 1 mm by 2 mm body

The TPS628302ARZER is the 2 A member of the TPS62830x family, a 2.25 V to 5.5 V input synchronous step down converter with an adjustable output from 0.5 V to 4.5 V. It shares the RZE WQFN body of 1 mm by 2 mm and the eight pin pinout with the 1 A, 3 A and 4 A members, so the difference between a 1 A and a 2 A rail on the same board is the order code and the passive parts around it, not the copper.

The control loop is DCS Control with a 2.0 MHz quasi fixed oscillator, a 500 mV feedback reference with a 495 mV to 505 mV window at 25 degrees, and 1 per cent output accuracy across minus 40 to plus 125 degrees junction. On resistance is 35 milliohm typical and 57 milliohm maximum for the high side at 5 V input, and 18 milliohm typical with 29 milliohm maximum for the low side. Quiescent current with the device not switching is 7 nA typical and 17 nA maximum, so the part does not give back at light load what it gains at 2 A.

At 2 A the loss budget changes shape. With a 57 milliohm maximum high side switch and a duty cycle of about 40 per cent for a 3.3 V output from a 4.2 V battery, the high side conducts about 91 milliwatt. The low side, conducting for the other 60 per cent at 29 milliohm maximum, adds about 70 milliwatt. Switching loss and inductor loss sit on top, and the total of roughly 250 milliwatt is what decides whether the 1 mm by 2 mm body is enough or whether the board needs the SOT583 body with more copper under it.

Key parameters from the SLVSG98B document

Input range2.25 V to 5.5 V with UVLO rising between 2.05 V and 2.25 V
Output range0.5 V to 4.5 V adjustable on the FB pin
Output current2 A rated on this member
Feedback voltage500 mV typical, 495 mV to 505 mV window, 1 per cent total error
Switching frequency2.0 MHz quasi fixed, PWM or PFM selected by the MODE pin
High side resistance35 milliohm typical and 57 milliohm maximum at 5 V input
Low side resistance18 milliohm typical and 29 milliohm maximum at 5 V input
Quiescent current7 nA typical and 17 nA maximum, not switching
Shutdown current100 nA typical and 700 nA maximum
Soft start180 to 440 microseconds to 95 per cent of the output, longer on the K options
ProtectionHiccup on short circuit, thermal shutdown at 150 degrees, output discharge on disable
PackageRZE WQFN of 1 mm by 2 mm, DRL SOT583 of 1.6 mm by 2.1 mm for the other members

What 2 A buys over 1 A on the same footprint

A 2 A part on a 1 A load runs at half the conduction loss of a 1 A part at its own limit, and that margin is what a customer buys when the ambient is 70 degrees or when the rail feeds a motor driver that pulls a surge at start. The trade is that the current limit moves up with the member, so the inductor and the output capacitor have to carry the larger peak. A 0.47 microhenry inductor with a 2.5 A saturation rating is adequate at 1 A and marginal at 2 A, and the inductor, not the converter, is the part that fails first.

Power good on this family is a window comparator rather than a single threshold: the open drain pin releases at 96 per cent of the nominal output and asserts again at 92 per cent, while the overvoltage side releases at 110 per cent and asserts at 105 per cent. There is a 128 microsecond delay at start up and a 30 to 60 microsecond deglitch in operation, which is long enough to ignore a load step and short enough for a sequencer.

The MODE pin is worth a note. In power save mode the output sits slightly high at very light load and the ripple becomes a burst pattern, which is fine for a display rail and bad for a radio. In forced PWM the part holds 2.0 MHz at no load and the no load current rises from nanoamps to milliamps. Products that sleep take power save, products that transmit take forced PWM.

Where this part fits

Point of load rails for wireless modules, camera and sensor boards, portable ultrasound front ends, handheld test instruments and any board that needs 2 A from a single lithium cell. The cross reference and the substitution notes for the family are at power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

Check the order code suffix, not the family. TPS628302ARZER is the 2 A part in the RZE body; the same string with a different digit is a different current, and the marking on the body is the only visible difference on a reel. Ask for the packing label with the full order code and keep it with the receipt record.

Check the thermal path. The RZE body is 1 mm by 2 mm and the exposed pad is the only way heat leaves, so the number of vias under the pad and the copper area around it decide the real current at 60 degrees ambient. A 2 A rail in a sealed enclosure that was signed off on a bench will derate. The receipt and solder check we run on these reels is described in incoming inspection plan.

Questions that come up on this part

Can the 2 A part be dropped onto a board that was laid out for the 1 A part, is the usual question. Inside the same package the pinout is identical and the passives are the same values, so the part will run, but the inductor and the output capacitor were chosen for the smaller current limit and have to be rechecked. A board that already has margin is a straight swap, a board that was tuned to the edge is not.

The second question is whether the output can be set to 5 V. It cannot, because the input range stops at 5.5 V and the output range stops at 4.5 V, so a 5 V rail from a 5 V bus needs a different family. The 100 per cent duty mode lets the output follow the input less the resistive drop, which is how the part behaves when the battery is nearly empty, not a way to make 5 V from 5 V.