Contact Us

TPS62816QWRWYRQ1

Brand: Texas Instruments
Texas Instruments TPS62816QWRWYRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62816QWRWYRQ1 — Power Management & Signal Chain | Superb Automation

TPS62816QWRWYRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62816QWRWYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62816QWRWYRQ1: an automotive 6 A step down converter in a 3 mm by 2 mm QFN with wettable flanks

TPS62816QWRWYRQ1 is a synchronous step down converter for automotive rails, with a 2.7 V to 6 V input, a 0.6 V to 5.5 V adjustable output and a switching frequency that can be set from 1.8 MHz to 4 MHz in a VQFN-HR (RWY) body of 9 pins. It delivers 6 A continuous, holds 26 microamp of quiescent current, keeps plus or minus 1 per cent output accuracy in PWM mode, and is qualified to AEC-Q100 grade 1 over minus 40 C to 125 C ambient with a junction range to 150 C.

Order code and package

TPS62816QWRWYRQ1VQFN-HR (RWY) body, 9 pins, 3.00 mm by 2.00 mm with wettable flanks, 3000 pieces on a large reel, nickel palladium gold or tin finish depending on the row, moisture level 2 at 260 C for one year, marking 816Q
Wettable flanksthe body is built so the solder joint can be inspected from the side after reflow, which is what an automotive line requires for a package this small
Suffixed rowthe addendum carries the string with an .A suffix, and the finish has to be read on the row rather than assumed
Packing3000 pieces on the large reel in the RWY body, which is the only body the document lists for this part
Temperatureminus 40 C to 125 C ambient for grade 1, with a junction range to 150 C
Marking816Q on every row, so a reel can be identified from the part marking when the label is gone

Electrical parameters that decide the application

Input voltage2.7 V to 6 V, which covers a 3.3 V and a 5 V automotive rail with tolerance
Output voltage0.6 V to 5.5 V adjustable by a divider, so the same part covers a core rail and a 5 V peripheral rail
Output current6 A continuous from the integrated switches, with the low resistance FETs keeping the conduction loss down at that current
Switching frequency1.8 MHz to 4 MHz set by a resistor on the COMP/FSET pin, or locked to an external clock in the same range on the MODE/SYNC pin
Frequency toleranceplus or minus 12 per cent on the resistor set frequency, which is what the synchronisation window has to allow for
Quiescent current26 microamp typical, which is what the standby current of an always on module depends on
Accuracyplus or minus 1 per cent in PWM mode, which is tight enough for a rail that feeds an analog reference
Duty cycle100 per cent maximum, so the output follows the input when the battery falls close to the rail
Soft startset by a capacitor, and the same pin makes the output track an external rail, which is how the sequencing between two supplies is held
Power gooda window comparator rather than a single threshold, so an overvoltage as well as an undervoltage pulls the output low
Modesforced PWM for constant frequency, or PWM and PFM for efficiency at light load, selected on the MODE/SYNC pin
QualificationAEC-Q100 grade 1, minus 40 C to 125 C ambient, with functional safety documentation available

Family variants and how they differ

COMP/FSET pina resistor to ground sets both the loop compensation and the switching frequency, which removes two decisions from the board and puts them in one component
MODE/SYNC pinselects forced PWM or PWM with PFM, and accepts an external clock when the rail has to run in step with the system
SS/TR pina capacitor sets the ramp and a divider makes the output track another rail, so sequencing and soft start come from the same pin
Spread spectrumavailable as an option in the family, which trades a small amount of output ripple for a lower emissions peak
Output dischargeactive discharge pulls the rail down when the converter is disabled, which matters when a module has to power down in a defined order

Points to check before this part goes on a BOM

The 3 mm by 2 mm body carries 6 A. That only works because the switches are low resistance and the pads are large, so the copper under the part is part of the current rating rather than a detail of the board.

Wettable flanks are an inspection requirement, not a marketing feature. An automotive line has to see the joint from the side, and a package without flanks cannot be inspected that way after reflow.

The frequency range is high. At 1.8 MHz to 4 MHz the inductor is small and the loop is fast, but the switching loss is real, so the thermal check at 6 A has to use the actual frequency rather than the lowest one.

The power good output is a window comparator. It pulls low on an overvoltage as well as an undervoltage, which is what a downstream load needs to see before it enables.

The frequency tolerance is plus or minus 12 per cent. A synchronisation clock has to fall inside that window, or the converter will not lock and will run on its own resistor set frequency instead.

What an automotive 6 A rail has to survive

A module that runs from a car battery sees the rail move from 3.0 V during a cold crank to more than 5 V during a load dump, and the converter has to hold the output through both. The 2.7 V to 6 V input range and the 100 per cent duty cycle are what make that possible without a second stage.

The qualification is the other half. AEC-Q100 grade 1 covers minus 40 C to 125 C ambient and the junction range goes to 150 C, and the functional safety documentation is what a tier one supplier asks for before the part goes on an approved vendor list.

The compensation resistor does double duty. It sets the loop response and the switching frequency at the same time, so a change of frequency moves the compensation with it. That is convenient on a first build and awkward on a second, because the two cannot be tuned independently once the board is fixed.

The remaining decision is the inductor value. At 2 MHz and a 3.3 V input a 0.22 microhenry part keeps the ripple inside the window the loop expects, and a larger value slows the response without improving the efficiency. The evaluation board in the document uses that value, and it is the safest starting point before the thermal check at 6 A.

Where this order code fits

It fits an infotainment head unit, an ADAS sensor module or a surround view ECU, where a 6 A rail has to come from the car battery in a body small enough to sit next to the load. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the part automotive qualified? Yes. It is qualified to AEC-Q100 grade 1 over minus 40 C to 125 C ambient, with a junction range to 150 C, and functional safety documentation is available.

What is the difference between forced PWM and PWM with PFM? Forced PWM holds a constant switching frequency across the load range, and PWM with PFM drops into a power save mode at light load. The first gives a cleaner spectrum, the second gives a lower standby current.

Why does the package have wettable flanks? So the solder joint can be inspected from the side after reflow, which is a requirement on automotive lines for a package this small.

Can two rails be sequenced? Yes. The SS/TR pin sets the start up ramp and can make one output track another, and the power good output gives the downstream rail a signal to wait for.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.