TPS62441RQRR
Product Specifications
TPS62441RQRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62441RQRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62441RQRR dual 1 A converter with an adjustable switching rate
The TPS62441RQRR is the 1 A plus 1 A member of the TPS6244x family, a dual channel synchronous step down converter that takes 2.75 V to 6 V in and delivers two independently enabled outputs between 0.6 V and 5.5 V. It is built on a peak current mode loop with an external compensation node, which is unusual in a family this small and is the reason it can be tuned for a fast transient rather than accepting a fixed internal loop. The switching rate is set by the MODE/SYNC pin, and the package is a QFN with two power grounds that have to be tied under the body.
The family spans three current combinations in one pinout: 1 A plus 1 A, 2 A plus 2 A, and 3 A plus 1 A, so a board can be scaled by part number without moving copper. The reference is 0.6 V with 1 per cent accuracy in PWM, quiescent current is 22 microamp typical and 66 microamp maximum with one channel enabled, rising to 33 microamp typical with both, and shutdown current is 1.5 microamp typical and 26 microamp maximum at 150 degrees junction. The undervoltage lockout is specified at 2.5 V, 2.6 V and 2.75 V across the falling edge, and thermal shutdown is at 170 degrees junction.
The enable thresholds are 1.06 V to 1.15 V on the rising edge and 0.96 V to 1.05 V on the falling edge, which is a logic level rather than a precise analog threshold. Each channel has its own power good output with a 94 to 98 per cent rising window and a 90 to 94 per cent falling window, so a processor can be told that both rails are inside tolerance rather than that the enables were asserted. The part is declared functional safety capable with documentation available for a safety case.
Key parameters from the SLUSEQ8A document
| Input range | 2.75 V to 6 V, with the lockout at 2.5 V to 2.75 V on a falling input |
| Outputs | Two channels at 1 A each on this member, adjustable from 0.6 V to 5.5 V |
| Reference | 0.6 V with 1 per cent accuracy in PWM and 80 nA of leakage at the feedback pin |
| Switching frequency | Set by the MODE/SYNC pin, with the option to synchronise to an external clock |
| Quiescent current | 22 microamp typical with one channel enabled, 33 microamp typical with both |
| Shutdown current | 1.5 microamp typical and 26 microamp maximum at 150 degrees junction |
| Enable thresholds | 1.06 V to 1.15 V rising, 0.96 V to 1.05 V falling, per channel |
| Power good | Per channel, 94 to 98 per cent rising window and 90 to 94 per cent falling, 0.07 V low level at 2 mA |
| Compensation | External, through the COMP pin, which is what allows the loop to be tuned to the output bank |
| Thermal shutdown | 170 degrees junction with hysteresis |
| Qualification | Functional safety capable, documentation available for a safety case |
| Package | QFN, two power grounds and two switch nodes brought out separately |
Peak current mode with an external compensation pin
Most converters in this size class hide the loop inside the package and ask the customer to trust the internal compensation across a range of output capacitors. This family brings the COMP node out, which means the loop can be stabilised against a specific output bank rather than a generic one. On an industrial board with a large capacitor and a long trace to the load, that is the difference between a converter that rings at 30 degrees of phase margin and one that does not ring at all.
The cost is a component and a calculation. A resistor and a capacitor from COMP to ground set the crossover and the phase boost, and the values depend on the output capacitance, the inductor and the load range. A board that copies the values from a reference board with a different output capacitor will be stable at one load and oscillate at another, and the oscillation appears as a low frequency envelope on the output rather than as a switching artifact.
Peak current mode also gives cycle by cycle current limiting without a separate sense resistor, because the switch current is compared against a threshold on every cycle. That is what makes the 1 A rating meaningful in a fault: the inductor current is bounded before the output voltage collapses, and the recovery is a soft restart rather than a hard fold back.
Where this part fits
Industrial motor drives, robotics controllers, instrumentation with two rails and any board where the loop has to be tuned to a specific output capacitor. The dual channel with independent enables and per channel power good is what makes it usable as a core and interface supply pair. Our desk keeps the family comparison across the 1 A, 2 A and 3 A members and the substitution notes, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
Check which current combination the board needs. The 1 A, 2 A and 3 A members share one pinout and one document, and a substitution changes the thermal and the current limit without changing a single pad. The external components around the COMP pin have to be re checked for the chosen member as well, since the loop gain depends on the switch current sense ratio.
Check the two ground pins and the thermal pad. A QFN with separate power grounds has to have both tied under the body with vias into the same plane, otherwise the switch current returns through the analog ground and the power good thresholds move with load. See incoming inspection plan for the receipt check on this body.
Questions that come up on this part
Can the two channels be paralleled to make 2 A, is a question that arrives with every dual converter. They cannot be paralleled directly, because two peak current mode loops driving one node will fight over the current share. A board that needs 2 A on one rail should use the 2 A member rather than two 1 A channels.
The second question is whether the switching rate can follow an external clock. The MODE/SYNC pin accepts a synchronisation signal, which is how a multi rail board keeps all converters on one carrier and avoids intermodulation in the input filter. The rate has to be inside the range the part supports, and the pin has to be driven rather than left floating.