HX52070D2
Product Specifications
HX52070D2
Hisiwell — Amplifiers & Comparators
Product Overview
The HX52070D2 from Hisiwell is a precision amplifier / comparator delivering high gain, wide bandwidth, and low distortion for signal conditioning. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High gain-bandwidth product for wideband signal amplification
- Low input offset voltage and drift for precision DC applications
- EMI-hardened design for robust operation in noisy environments
- Rail-to-rail input/output for maximum dynamic range
- Low quiescent current for power-sensitive designs
- Unity-gain stable with capacitive load drive capability
Key Specifications
| Channels | — |
| GBWP | MHz |
| Slew Rate | V/µs |
| Vos | µV |
| Iq per Channel | µA |
| Input Type | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
HX52070D2: 18 dBm of compression in a 2 x 2 mm package, and the half dB that protects it
The HX52070D2 is the highest power gain block in this series: DC to 10 GHz, 20 dB of gain, 18 dBm at the 1 dB compression point, 65 mA from 5 V, in a 2 x 2 mm DFN. It is 4.5 dB above the 14 dBm members of the family in output power and it covers the widest band. It is also the part in the group with the smallest margin between compression and saturation, half a dB.
What the vendor publishes
| Parameter | Value |
|---|---|
| Frequency range | DC to 10 GHz |
| Gain | 20 dB |
| Output P-1dB | 18 dBm at 1 GHz |
| Output Psat | 18.5 dBm |
| Noise figure | 3.5 dB |
| Input return loss | 18 dB, 1.29:1 |
| Output return loss | 22 dB, 1.17:1 |
| Output IP3 | 29 dBm at 1 GHz |
| Supply | +5 V, 65 mA |
| Package | 2 x 2 mm DFN-6L |
Half a dB between compression and saturation
18 dBm at compression and 18.5 dBm at saturation means the output clips within half a dB of the point where the specification is taken. There is no soft knee to absorb an overshoot, a transient at power up, or a transmitter that briefly drives harder than the nominal level. A limiter ahead of it, or 3 dB of backoff in the level plan, is what keeps a 1.26 W amplifier stage from being asked to deliver 1.4 W. The same numbers make the part attractive for a fixed level application where nothing changes: 18 dBm into a level 7 mixer LO port, or 18 dBm as the driver of a final stage.
The best conversion in the family
At 5 V and 65 mA the DC input is 0.325 W. At 18 dBm the output is 0.063 W, which is 19.4 percent conversion at compression, the highest ratio in the family, twice the 9.6 percent of the low current part. That is what the extra 32 mA buys. It also means 0.26 W of heat in the smallest package in the family, so the paddle connection is not optional: the DFN has to sit on a copper area with a via array, and the ground return has to be continuous under the part.
DC to 10 GHz in one stage
The band edges mark this apart from the other members, most of which stop at 3 or 6 GHz. A single stage that holds gain and match from DC to 10 GHz removes a band split from a wideband receiver front end. The input match of 18 dB and the output of 22 dB are ordinary for the family, so nothing here needs a pad or a matching network added to work.
Linearity at the top of its range
The intercept of 29 dBm sits 11 dB above compression. Two tones at 12 dBm each at the output give third order products about 34 dBc down, and at 8 dBm per tone about 42 dBc. That is the honest linearity picture for a part that is being used near its ceiling: useful for a driver, not for a multicarrier transmit path where the products have to sit below a spectral mask at high output.
Two questions buyers ask
Is 65 mA at 5 V acceptable in a handheld product? 0.325 W is high for a battery powered receiver, but this is not a receiver first stage. Where the rail is limited, the 12 dB part on the same family draws 40 mA with 5.5 dB less output power.
Does it need a negative supply? No. The table gives a single +5 V rail, no gate bias. That is one of the practical differences between this family and the bare die amplifiers in the same catalogue, which mostly need a negative gate and a sequencing order.
SUPERB supplies the HX52070D2 with the vendor table confirmed against the lot. If you are substituting it for a lower power part already on the board, the amplifier cross reference hub lists what has to be checked first. For obsolescence on the device it replaces, see obsolete RF part replacement. Stock for the HX52070D2 is quoted from the amplifiers and comparators index.
Request Quote — In Stock, 100% New & Original, Full Warranty