Contact Us

TPS6209733RWKR

Brand: Texas Instruments
Texas Instruments TPS6209733RWKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS6209733RWKR — Power Management & Signal Chain | Superb Automation

TPS6209733RWKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS6209733RWKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS6209733RWKR: 2 A step-down converter with selectable frequency

TPS6209733RWKR is a synchronous step-down converter aimed at noise-sensitive 2 A rails in a VQFN body of 11 pins. It runs from 2.5 V to 6 V, delivers 2 A, switches between 1.5 MHz and 2.5 MHz set by one external resistor, holds 1 percent output accuracy, and reaches 97 percent efficiency at medium load.

Order code and package

Ordering stringTPS6209733RWKR, RWK package, tape and reel, 3.3 V fixed option
Package11-pin VQFN, 2.00 mm by 2.00 mm
Output optionsFixed 1.8 V and 3.3 V, plus an adjustable version from 0.8 V to VIN
Ambient rangeJunction -40 C to 125 C
Successor noteThe vendor points to the TPS62851x family as the newer option for this class

Electrical parameters that decide the application

Input range2.5 V to 6.0 V
Output current2 A continuous
Switching frequency1.5 MHz to 2.5 MHz, selected by an external resistor
AccuracyPlus or minus 1 percent over the specified conditions
EfficiencyUp to 97 percent
ModesForced PWM for fixed frequency, or power save at light load
FeaturesProgrammable soft start, output tracking, power-good, output discharge

Points to check before this part goes on a BOM

One resistor sets the switching frequency between 1.5 MHz and 2.5 MHz, and that resistor is a system decision rather than a detail. Running at 2.5 MHz keeps the switching energy above the band where an audio or an intermediate-frequency stage listens, and it shrinks the inductor, at the cost of switching loss and a tighter on-time at high input. At 1.5 MHz the efficiency is better and the ripple is worse, and the inductor is the part that grows.

A 2 mm by 2 mm body with an 11-pin count means the thermal path is the pad under it. At 2 A into 1.8 V from 5 V the converter dissipates roughly 0.3 W including switching, and that is only manageable because the frequency is high and the inductor is small. Push the same part to 2 A into 1.2 V from 5 V and the loss rises while the copper available to remove it does not.

Forced PWM holds the frequency fixed at light load, which keeps the output ripple a known shape and avoids the low-frequency burst that a power-save mode produces. The cost is quiescent loss: a rail that sits at 1 mA most of its life is better in power-save mode, while a rail that feeds an ADC or a radio is better in forced PWM. The mode is a pin setting, not a software decision, so the pin carries the choice.

One percent accuracy is the whole point of the fixed 1.8 V and 3.3 V options: no divider, so no divider tolerance and no divider drift. A board that needs 1.2 V has to use the adjustable member and then owns the error of two resistors, which is typically larger than the regulator's own 1 percent. That difference is often the reason a board stays at 1.8 V.

Hiccup short-circuit protection means a fault does not sit at the current limit cooking the inductor. The converter shuts down, waits, retries, and repeats, so the average dissipation during a short is a fraction of the limit power. For a load that can present a soft short at power-up, this is the difference between a recoverable event and a burnt board.

The output discharge circuit pulls the rail down when the converter is disabled, which matters when the same 1.8 V rail feeds a processor that must not see a floating supply while the rest of the board is still alive. Without it, a disabled rail decays through leakage and can hold a logic input in an undefined state for milliseconds.

The internal compensation allows an output capacitor well above the usual few tens of microfarads, which matters when the 2 A rail feeds a load that steps hard, or when the same rail is shared with a connector that a user can plug into. A large ceramic bank lowers the impedance at the load and the converter stays stable because the loop was specified for it. The limit is the inrush at start-up, which the programmable soft start controls: without it, a large bank looks like a short to the input for the first few milliseconds.

Where this order code fits

It fits a 3.3 V or 1.8 V rail from a single-cell or 5 V input in a handheld instrument, a camera module or a radio board, where 2 A is the ceiling and switching noise has to stay out of a known band. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the 3.3 V option really fixed? Yes. The RWK ordering string with the 33 suffix is the 3.3 V fixed part, and the feedback divider is internal. Boards that need another voltage buy the adjustable member of the same family.

Should I fit the newer family instead? Compare the pinout and the input range first. The newer family is a different package and a different pin count on most variants, so it is a board change rather than a substitution. For an existing build this part remains orderable and in production.

What sets the frequency resistor value? The data sheet table maps resistor to frequency between 1.5 MHz and 2.5 MHz. The resistor is a 1 percent part in practice, because its tolerance moves the frequency and therefore the ripple and the EMI spectrum.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.