TPS562210DDFR
Product Specifications
TPS562210DDFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS562210DDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS562210DDFR: a 2 A synchronous buck in an eight pin SOT-23 body that runs from 4.5 V to 17 V at a fixed 650 kHz with no external compensation
TPS562210DDFR is a step down converter with both FETs inside the package, an emulated on-time control loop that is stable with ceramic output capacitors, and a fixed switching frequency that lets a small inductor be chosen without a loop calculation in a SOT-23-THIN body of 8 pins. The DDF body is 1.60 mm by 2.90 mm on eight pins, and the part is the 2 A member of a two part family whose 3 A sibling uses the same pinout with smaller FETs.
Order code and package
| Catalogue string | TPS562210DDFR, the R letter being the large reel row in the vendor addendum |
| Body | SOT-23-THIN, DDF, eight pins, 1.60 mm by 2.90 mm |
| Reel | 3000 pieces on a large reel for the R row, 250 pieces on a small reel for the T row, both in the same body |
| Finish and moisture | CU SN plating, green and RoHS with no antimony or bromine, moisture level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 125 C on the addendum, while the electrical tables are written to 85 C ambient for most rows |
| Marking | 2210 on the 2 A rows and 3210 on the 3 A rows, which is the only visual difference between the two parts |
| Document | SLVSCM6A, February 2015, revised August 2015 |
| Family split | TPS562210 is the 2 A member with 133 mOhm and 80 mOhm FETs, TPS563210 is the 3 A member with 68 mOhm and 39 mOhm, and the addendum prints the 3 A rows as NRND |
Electrical parameters that decide the application
| Input range | 4.5 V to 17 V, which covers a 5 V rail, a 12 V rail and a 15 V rail without a pre regulator |
| Output range | 0.76 V to 7 V set by a divider, with the feedback threshold at 0.765 V typical, 758 to 772 mV at 25 C and 751 to 779 mV over minus 40 to 85 C |
| Output current | 2 A continuous, and the current limit is printed as 2.5 A minimum, 3.2 A typical and 4.3 A maximum with a 2.2 uH inductor |
| Switching frequency | 650 kHz fixed, so the inductor and the output capacitor are chosen against a known ripple rather than a range |
| FET resistance | 133 mOhm high side and 80 mOhm low side at 25 C with 5.5 V of gate drive, which is where the conduction loss comes from at 2 A |
| Quiescent current | 190 uA typical and 290 uA maximum while switching, and 3 uA typical with 10 uA maximum in shutdown |
| Enable thresholds | 1.6 V high and 0.6 V low, with a 225 to 900 kOhm internal pull down that keeps the part off while the driving pin floats |
| Duty limit | 65 per cent maximum recommended, which sets the minimum input for a given output as the output divided by 0.65 rather than by one |
| Protection | cycle by cycle current limit, hiccup mode on an output undervoltage, non latching overvoltage at 125 per cent of the feedback threshold, and thermal shutdown at 155 C with 35 C of hysteresis |
| Power good | open drain output that releases between 85 and 95 per cent of the feedback threshold on the way up, 90 per cent typical, and pulls low 5 per cent below it on the way down |
| Soft start | an external capacitor on the SS pin charged at 6 uA typical, which sets the ramp without changing the control loop |
| Thermal | the eight pin body has no thermal pad, so the copper under the pins is the only heat path and the 2 A rating has to be checked against the board rather than assumed |
The two family members and the status of each
| TPS562210DDFR | 2 A, 133 and 80 mOhm, 3000 pieces large reel, marking 2210 |
| TPS562210DDFT | the same die on 250 pieces small reel, marking 3210 on that row |
| TPS563210DDFR | 3 A, 68 and 39 mOhm, same body and pinout, printed NRND with Call TI against the finish column |
| TPS563210EVM-652 | the evaluation module row, which appears in the same packaging table as a preview line |
| TPS56x210 point of comparison | the family is the smallest of the D-CAP2 converters, and a 4 A or 6 A load moves to the TPS54625 or the TPS545xx parts rather than to a parallel pair |
Points to check before this part goes on a BOM
The 3 A sibling is not a free upgrade. The addendum prints the TPS563210 rows with the NRND status and Call TI in the finish column, while the 2 A rows carry the standard CU SN finish and a real quantity. A BOM that was written when both were active and that names the 3 A part is therefore a BOM with a part on the way out, and the honest move is either to buy the 2 A part and accept less headroom or to move to a current family. This is the sort of thing that shows up as a line down six months after the prototype, so it is worth settling before a programme freeze rather than after.
The feedback threshold is 0.765 V and the division is exact. A 1.05 V output needs a divider ratio of 1.05 over 0.765, which is 1.3725, so a 3.74 kOhm upper resistor against a 10.0 kOhm lower one lands on the value the vendor's own example uses. A divider copied from a 0.8 V reference part produces an output about 4.5 per cent high, which on a 1.05 V core rail is 48 mV of margin gone before the load regulation is counted.
The 65 per cent duty limit is what sets the minimum input, and it is easy to miss. At 1.05 V out the arithmetic gives 1.62 V minimum, which is far below the 4.5 V floor and never binds. At 5 V out the same arithmetic gives 7.7 V, so a converter running 5 V from a 6 V input is outside the recommended operating area even though the part is rated to 4.5 V on the input. The input range and the duty limit are two separate constraints and both have to hold.
The current limit window is wide, 2.5 to 4.3 A on a 2 A part, and that is deliberate. The limit is sensed across the low side FET, so it tracks the FET resistance and moves with temperature and with the inductor value. A load that draws 2.4 A steady state sits above the minimum limit and may or may not trip depending on the board, which is a bad place to be. A load that draws 2.0 A and peaks at 2.8 A in a transient is fine, because the transient is shorter than the hiccup counter's patience.
Hiccup mode on an undervoltage is the right choice for a point of load converter and the wrong one for a rail that has another supply on it. When the output falls below the undervoltage threshold the part stops, waits, and restarts, which limits the dissipation in a shorted load. On a rail that is paralleled with a second source, the restart is a current pulse into a node that is already powered, and the two supplies fight for a few hundred microseconds on every retry. Where a second source is present, the protection has to be arranged so the converter does not retry into a live node.
An eight pin SOT-23 body with no thermal pad removes any assumption about junction temperature. At 12 V in, 1.05 V out and 2 A, the conduction loss on the high side is short because the duty is 8.75 per cent, and the low side carries 1.83 A for 91 per cent of the period at 80 mOhm, which is 268 mW. Switching loss and the gate charge add to that, and the total lands near half a watt inside a body whose junction to ambient resistance is around 60 to 80 C per W on a modest copper area. That is a 30 to 40 C rise, which is a real limit on a 70 C enclosure.
Reading the current limit against a real load
The published limit is a DC figure measured with a 2.2 uH inductor at 1.05 V out. Change the inductor to 1.5 uH and the ripple current rises by half, which changes the point at which the valley of the ripple crosses the limit. A load that is safe on the vendor's benchmark can trip on a board with a smaller inductor, and the difference is not in the headline number. Where a load is close to 2 A, the inductor value and the input voltage both belong on the test plan.
The hiccup response is what makes a limit survivable. A hard short produces a current spike that the comparator catches within a cycle, and the part then stops for a fixed count before trying again. That count is long enough that the average dissipation in a short is small, and it is also long enough that a load which needs more than the limit for a few milliseconds will see the rail collapse rather than a clean current fold back. A motor start or a disk spin up is that kind of load and belongs on a rail with a bigger converter.
Choosing the output capacitor for a D-CAP2 loop
The loop is built to be stable with ceramic capacitors and with polymer parts, and it does not need the external compensation network that a voltage mode controller needs. That is the main reason the pin count is eight. What it does need is enough capacitance that the ripple at the feedback pin stays inside the internal ramp, because the control uses the output ripple as part of its timing. A rail with too little capacitance runs at a higher effective frequency and can show jitter that looks like instability.
The practical starting point is 2 by 22 uF of ceramic for a 2 A rail, which is what the vendor's own example uses, and the ripple works out at about 20 mV peak to peak at 1.05 V. Reducing that to one capacitor saves board area and moves the ripple to 40 mV, which on a 1.05 V core rail is nearly 4 per cent and is enough to upset a processor that expects a quiet supply.
Where this order code fits
This is the point of load converter behind a 12 V or 5 V bus on a set top box, a digital television, a network terminal or an industrial controller, where a 2 A rail has to be generated from a bus that is already regulated Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.
Questions buyers ask
Is the 3 A version a drop in? Same body, same pins, smaller FETs, and the addendum prints the 3 A rows as NRND. It works on the same footprint and it is not a part to start a new build on.
What sets the output voltage? A divider from the output to the feedback pin, with the threshold at 0.765 V. A 3.74 kOhm upper resistor against 10.0 kOhm gives 1.05 V.
Can it run from 5 V in and 5 V out? No. The maximum recommended duty is 65 per cent, so a 5 V output needs at least 7.7 V of input even though the part is rated from 4.5 V.
Is there a thermal pad? No. The eight pin SOT-23-THIN body has no exposed pad, so the copper under the pins carries the heat and the 2 A rating depends on the board.
What does the power good pin do? It is an open drain output that releases between 85 and 95 per cent of the feedback threshold on the way up and pulls low 5 per cent below on the way down, so it can drive a sequencing input directly.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.