Contact Us

TPS562208DDCR

Brand: Texas Instruments
Texas Instruments TPS562208DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS562208DDCR — Power Management & Signal Chain | Superb Automation

TPS562208DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS562208DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS562208DDCR: 2 A synchronous buck, 4.5 V to 17 V input, 580 kHz, forced continuous, SOT-23-6

TPS562208DDCR is a 2 A synchronous step down converter with both switches inside a six pin SOT-23 body, running at a fixed 580 kHz from a 4.5 V to 17 V input in a SOT-23-6 body of 6 pins. The two switches measure 140 milliohm on the high side and 84 milliohm on the low side at 25 degrees. Control is D-CAP2 with no external compensation and no COMP pin, and the feedback threshold is 768 mV typical with a 2 per cent window at 25 degrees. This member of the pair keeps switching at light load, which holds the ripple frequency steady for a rail that feeds an analogue circuit or a clocked load.

Order code and package

TPS562208DDCRActive, SOT-23-THIN (DDC) body, 6 pins, 3000 pieces on a large reel
TPS562208DDCTActive, the same body with 250 pieces on a small reel
TPS562201DDCRActive, same silicon with pulse skip at light load instead of forced continuous, same 3000 piece reel
Temperature rangeminus 40 to 125 degrees junction on every published row
Switching frequency580 kHz fixed, no resistor to set it

Electrical parameters that decide the application

Input voltage4.5 V to 17 V
Output voltage0.76 V to 7 V, set by a divider into the VFB pin
Output current2 A continuous
Switch resistance140 milliohm high side, 84 milliohm low side at 25 degrees
Feedback threshold768 mV typical, 749 to 787 mV over temperature
Supply current350 microamp typical, 500 maximum, not switching, for this string; 120 microamp for the pulse skip member
Current limit2.4 A minimum, 3.2 A typical, 4.0 A maximum
Soft start and minimum off time1.0 ms fixed soft start, 220 to 310 ns minimum off time

Family variants and how they differ

TPS562208forced continuous conduction at light load, the string on this page
TPS562201pulse skip at light load, 120 microamp quiescent instead of 350
TPS563208the 3 A member with 95 and 57 milliohm switches, same body and same pin out
Enable threshold1.6 V high, 0.8 V low, with a 600 to 2400 kilohm pulldown
Protectioncycle by cycle current limit, hiccup on a persistent fault, non latching undervoltage and thermal shutdown at 160 degrees

Points to check before this part goes on a BOM

Four and a half volts is the input floor and it is above a 3.3 V bus. The converter cannot post regulate a 3.3 V rail, and a 5 V rail at minus 10 per cent sits at 4.5 V with no margin at all. A 12 V adapter, a 5 V rail with a tight tolerance or a 9 V supply are the intended sources. A board that needs to run from 3.3 V needs a different part and the difference shows up as a converter that never starts.

Seventeen volts suits a 12 V bus with margin, not a 24 V bus. A 12 V rail at plus 10 per cent reaches 13.2 V and an industrial transient seldom passes 16 V. A 24 V bus is above the rating before tolerance, and a vehicle rail with load dump is far outside it. Offering this string for a 24 V input is the single most common wrong quote on this family.

The feedback window is wider than the headline accuracy suggests. The front page quotes 2 per cent at 25 degrees, and the electrical table shows 749 to 787 mV across the full range against a 768 mV nominal. That is about 5 per cent end to end. A rail that has to hold a tight window at temperature needs the divider tolerance added to that, and the divider resistors are usually the larger error.

Forced continuous conduction is the reason to pick this string. At light load the low side switch keeps conducting in the normal cycle, so the switch node stays at 580 kHz and the ripple does not fall into the audio band. That is what a rail feeding an ADC, a codec or a radio wants. The cost is quiescent current: 350 microamp typical against 120 microamp for the pulse skip version, which matters on a product that sleeps on battery.

The current limit is measured on the high side switch, not on the load. The minimum point is 2.4 A, which is above the 2 A rating, so the converter delivers its rated current with ripple on top and does not fold back early. A sustained overload drives the part into hiccup: a short switching window, a long pause, repeated. A fixture that reads the output during a fault sees a pulsing voltage, not a clean zero.

A 1 ms soft start with a large output capacitor is a compromise. The fixed ramp is short enough that a 470 microfarad bank looks like a load step at power up, and the converter hits its current limit before the output arrives. The result is a longer, staircase ramp instead of a clean one. Either keep the output capacitance inside the range the application section gives or sequence the enable from a supervisor that tolerates the extra time.

The minimum off time sets the maximum duty cycle and therefore the dropout. At 580 kHz and 310 ns, the part can hold roughly 82 per cent duty, so a 12 V input can regulate a 7 V output but a 5 V input cannot hold 4.5 V at full load. The dropout is resistive, made of the high side switch and the inductor, and it grows with load. A rail that sits close to the input has to be checked at the lowest input and the highest current together.

No compensation pin means the output capacitor is the loop. D-CAP2 is stable with low ESR ceramic capacitors across a range, but a board that swaps a 22 microfarad part for 220 microfarad to chase ripple changes the loop and can ring on a load step. The value after bias derating is what the loop sees, and a 10 V rated 22 microfarad ceramic at 5 V loses a large part of its capacitance.

Packing is a real difference between the two strings. DDCR ships 3000 pieces on a large reel and DDCT ships 250 on a small reel from the same silicon. A prototype build of 200 pieces is cheaper on the small reel and a production run on the large one, and mixing the two means a line stop for a reel change that was not planned.

The 3 A member is a drop in for this footprint. TPS563208 shares the body, the pin out and the 580 kHz frequency and differs in the switch resistance. When a 2 A rail turns out to need margin, the upgrade does not touch the board, and the current limit scales with it. That is worth stating on an offer because it removes a re-spin from the customer risk list.

What to confirm before this part goes on a purchase order

Name the input bus, the output voltage and the load current together. The same string covers a 12 V to 5 V rail and a 12 V to 1.2 V rail, and a substitute offered without the bus voltage cannot be checked for duty cycle or thermal margin.

Say whether the rail sleeps. Forced continuous conduction is the right choice for a rail that feeds an analogue load and the wrong one for a product that spends most of its life in standby, and the two strings are not interchangeable on that point.

Where this order code fits

It makes a 5 V or 1.2 V rail at 2 A from a 12 V adapter in a set top box, a television main board or a network appliance, where the rail feeds a clocked or analogue load and the switching spectrum has to stay at a fixed frequency all the way down to no load. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it produce 3.3 V from a 5 V input at 2 A? At 5 V in and 3.3 V out the duty cycle is 66 per cent, which is inside the 82 per cent the minimum off time allows, so the converter regulates. The margin is thin at the low end of the input tolerance: at 4.5 V the duty cycle is 73 per cent and the resistive dropout of the high side switch and the inductor starts to show at full load.

Why does the quiescent current look high for a modern part? Because this string never stops switching. The 350 microamp figure is the supply current with the switch node running at light load, not a sleep current. The pulse skip member of the same family draws 120 microamp in the same condition and is the one to quote for a battery product.

What happens if the output is shorted? The high side current limit trips at 2.4 A minimum and the part enters hiccup, switching for a short window and then pausing. The output pulses at a low frequency until the short is removed, and the part recovers without a power cycle because the protection is not latching.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.