TPS3780DDRYR
Product Specifications
TPS3780DDRYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3780DDRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3780DDRYR: Dual-channel voltage detector, 1.5 V to 6.5 V, 2 microamp, open-drain outputs
TPS3780DDRYR is a two-channel voltage detector with 1 percent threshold accuracy and factory-set hysteresis for rail monitoring and sequencing in a SON (DRY) body of 6 pins. It watches two rails through external dividers, sinks its open-drain outputs when either sense pin falls below its threshold, and draws 2 microamp from a supply that can be as low as 1.5 V.
Order code and package
| Ordering string | TPS3780DDRYR, DRY package, 6-pin SON, tape and reel |
| Family members | TPS3780 (open drain), TPS3779 (push-pull); each in four hysteresis options |
| Package | 6-pin SON, 1.45 mm by 1.00 mm, and a 6-pin SOT-23 at 2.92 mm by 1.30 mm |
| Ambient range | -40 C to 125 C |
| Pin count check | VDD, GND, SENSE1, SENSE2, OUT1 and OUT2 |
| Output type | Open drain, pull-up allowed to 6.5 V independently of VDD |
Electrical parameters that decide the application
| Supply range | 1.5 V to 6.5 V |
| Threshold accuracy | 1.0 percent over temperature on both channels |
| Sense threshold | 1.2 V nominal, so a divider sets any monitored rail above that |
| Hysteresis options | 0.5 percent, 1 percent, 5 percent and 10 percent, factory set by order code |
| Quiescent current | 2 microamp typical, which is what allows a permanent connection to a battery rail |
| Output current | Sinks and sources the level a reset input needs, with the open-drain version pulling to ground only |
| Power-on reset | Outputs are undefined below the internal power-on threshold, so the host must not rely on them there |
Points to check before this part goes on a BOM
The 1.2 V sense threshold fixes the divider arithmetic. For a 3.3 V rail going low at 3.0 V, the divider ratio is 1.2 over 3.0, which is 0.4, so R2 over the sum of R1 and R2 equals 0.4 and a 100 kohm total gives 40 kohm and 60 kohm. The 1 percent threshold accuracy and the resistor tolerance then add, and 1 percent resistors turn a 3.0 V trip point into a 2.97 V to 3.03 V window before temperature is counted.
Two microamp is the figure that makes this part usable on a standby rail. Over a year it is 17.5 mAh, which is small against any cell, and it is the reason the detector can be left on a battery rail while the rest of the board is off. Any divider across that rail adds to it: a 100 kohm total divider at 3.3 V draws 33 microamp continuously, sixteen times the detector, and a 1 Mohm divider brings it back to 3.3 microamp.
The hysteresis option is a choice about false trips, not about accuracy. At 0.5 percent on a 3.3 V rail the release point is 16 mV above the trip point, which a noisy rail will cross repeatedly, and at 10 percent it is 330 mV, which a slowly rising supply may never reach. A 5 percent option is what most sequencing circuits take, because it sits between the two failures.
Divider current versus bias current is the second decision. The data sheet asks for roughly 100 times the sense pin bias current in the divider, and the bias current is small enough that 1 Mohm is acceptable. The cost of that choice is noise pickup on a high impedance node, so a 10 nF capacitor across the lower resistor is usual in a switching environment and it does not change the trip point.
Response time depends on overdrive, and the data sheet says so directly. A rail that crosses the threshold by 1 percent produces a slow output transition, and one that crosses by 10 percent is fast. In a brownout case the rail usually falls quickly and the detector is fast, but in a slow battery discharge the same detector lags by tens of microseconds more than the bench test suggests, which matters only if the host is expected to save state.
The open-drain outputs also allow wired-AND. Tying OUT1 and OUT2 to one pull-up and feeding a single reset input means either rail failing holds the host in reset, which is the usual arrangement when a 3.3 V core rail and a 1.8 V I/O rail have to come up in a defined order. The pull-up has to go to a rail that is alive before either monitored rail, or the reset line will be undefined during power-up.
Both channels share one ground and one supply, so their thresholds track each other with temperature and with supply variation. That is useful when the two rails are meant to move together, and it is a problem when one of them is a 1.2 V core and the other a 12 V field rail, because the divider on the 12 V side has to divide by ten and the tolerances no longer match. The two sense pins also share the same bias current specification, which is why a 1 Mohm divider is acceptable on both, and why the noise on the higher voltage divider is the one that needs the capacitor.
Where this order code fits
It is used for under voltage and power good monitoring in DSP, microcontroller and FPGA systems, in portable medical devices, building automation nodes, solid state drives and any board that has to hold a processor in reset until two rails are inside tolerance. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it monitor a rail below 1.2 V? Not directly. The sense threshold is 1.2 V, so the monitored rail has to be above that, and a 1.0 V core rail needs a different detector or an additional reference.
What pull-up value should the output use? The part sinks the current a reset pin needs, so the resistor is chosen from the sink current and the rise time of the line, and a few hundred kiloohm is normal on a CMOS reset input.
Does the 0.5 percent option make the trip point more accurate? No. Accuracy is 1 percent on every option. The percentage in the order code is the hysteresis, meaning how far the rail has to recover before the output releases.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop RF Supply page sets out the checks that keep a substitute from failing on the bench.