TPS3707-50DR
Product Specifications
TPS3707-50DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3707-50DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3707-50DR 5 V processor supervisor with a power fail comparator
The TPS3707-50DR watches a 5 V rail and holds a processor in reset until that rail is above 4.55 V, then releases the reset after a fixed 200 ms. It also carries a separate power fail comparator with its own input, so a board can warn the processor before the rail actually collapses and give it time to store what it was doing. Both functions sit in an 8 pin body that predates most of the parts around it on the board.
The family is worth reading as a group. The TPS3705 members add a watchdog timer with a window input and a watchdog output, and the TPS3707 members on this page do not, which is the reason this order code is chosen for a board that feeds its own watchdog in software. Both share the 200 ms reset, the manual reset input and the power fail comparator, and both are printed as pin for pin compatible with the MAX705 to MAX708 line, which is what makes them a replacement candidate for older boards.
Key parameters taken from the TPS370x document
| Monitored rail | 5 V option, negative going threshold 4.45 V minimum, 4.55 V typical, 4.65 V maximum |
| Reset delay | 200 ms fixed, no external capacitor needed |
| Reset output | Push pull active low, with the output defined from a 1.1 V supply |
| Supply current | 50 microamp maximum, which is the ceiling for the whole part rather than a typical figure |
| Power fail comparator | Separate input and output pair, driven from the rail through an external divider, so the warning level is set by the customer |
| Manual reset | Input fitted, a low level forces the reset active |
| Watchdog | Not fitted on the TPS3707 members. The TPS3705 members carry the timer, the window input and the watchdog output |
| Temperature | Minus 40 to plus 85 degrees C, with the 3.3 V member of the family rated to 125 degrees C |
| Packages | 8 pin SOIC and 8 pin MSOP with a PowerPAD, the D and DGN bodies |
| Compatibility | Printed as pin for pin compatible with the MAX705 through MAX708 series |
| Revision | Document revised October 2020, first issued November 1998, which is the reason the electrical table carries both a 25 degree and an over temperature window |
The threshold window of 4.45 V to 4.65 V is the first row to read carefully. A 5 V rail at minus 5 per cent is 4.75 V, comfortably above the maximum, and a rail at minus 10 per cent is 4.5 V, which sits inside the window. That is deliberate: the part is meant to assert below the tolerance of a 5 V supply, not inside it.
Where the numbers matter in a real build
The power fail comparator is the feature that keeps this family on boards after thirty years. The divider on the power fail input is set by the customer, so the warning can fire at 4.9 V while the reset threshold sits at 4.55 V, and the processor then has the difference between the two levels to flush a buffer into flash. The window between them is a time budget, and it depends on the bulk capacitance on the rail rather than on the supervisor at all.
The 50 microamp ceiling is a maximum over temperature, which is a different statement from a typical figure. A board that budgets 20 microamp for a supervisor and then fits this part will find the number three times higher at 85 degrees, and that matters on a product that runs from a battery or from a 4 to 20 mA loop.
The 200 ms delay is fixed and cannot be shortened. A processor that boots in 40 ms will still wait 200 ms after the rail is good, which is invisible on a mains powered product and measurable on a battery product that wakes, measures and sleeps. Where that time is unacceptable the same family is not the answer, and the smaller SC-70 supervisors with a 100 ms delay are the ones to look at.
What to check before a purchase order is released
- Whether the drawing expects a watchdog, because the TPS3705 parts carry one and this order code does not.
- The power fail divider, which sets the warning level and has to be calculated from the actual rail rather than copied from an application note.
- The reset polarity, which is active low and push pull, so it cannot be wire ORed with a second open drain reset source.
- The package choice, because the DGN body is an MSOP with a thermal pad and the D body is a plain SOIC, and the two do not share a footprint.
- The temperature grade, since the 5 V member is rated to 85 degrees C and a cabinet at 70 degrees ambient with a 20 degree rise leaves no margin.
- The pull up on the power fail output, because it is an open drain pin on this family.
Which projects this part fits
The vendor lists equipment built around DSPs and microcontrollers, industrial controllers, programmable controls, automotive systems, portable and battery powered instruments, wireless communication systems and computers. The power fail comparator makes it a natural fit for a product with non volatile memory that has to be written safely on the way down, and the MAX705 compatibility makes it a replacement candidate for a board whose original part has gone obsolete.
Questions that come up before a purchase order is released
Can a TPS3707 part replace a TPS3705 part?
On the footprint yes, on the function no. The watchdog input and the watchdog output are live on the 3705 and unused on the 3707, so a board that relies on the watchdog will lose it silently.
Does the part need an external capacitor for the reset delay?
No. The 200 ms delay is fixed inside the device, which is one of the reasons it stays on boards that have very little room.
What happens when the rail collapses slowly?
The reset asserts as the rail crosses the threshold and stays asserted while the supply is above 1.1 V. Below that the output state is not defined, so a slow decay through 1 V is the point where an external pull down or a different arrangement matters.
Is the manual reset input debounced?
The input is a comparator against the threshold with the internal delay applied to the output, so a noisy push button still needs a capacitor or a software filter on the board.
How SUPERB handles this line
Parts like this one are usually ordered as a replacement for a device that a drawing already names, so the usable service is a cross reference and a reel split rather than a catalogue entry. Our power management cross reference covers the supervisor families that map onto each other, and the lead time page explains what we can do when a distributor shows a year. When a board has to keep running with a part that is no longer made, the obsolete part cross reference hub is where we start.