Contact Us

TPS7A3901DSCR

Brand: Texas Instruments
Texas Instruments TPS7A3901DSCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A3901DSCR — Power Management & Signal Chain | Superb Automation

TPS7A3901DSCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A3901DSCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A3901DSCR: dual positive and negative 150 mA regulator from a plus or minus 33 V input

TPS7A3901DSCR is one package carrying a positive and a negative low dropout regulator, each rated 150 mA, each able to work from a rail of up to 33 V in magnitude, with a single enable and a buffered 1.2 V reference in a WSON body of 10 pins. The TPS7A39 puts a positive regulator and a negative regulator on one die. Each channel takes an input of 3.3 V to 33 V in magnitude, delivers 5 mA to 150 mA, and sets its output from the 1.19 V reference: positive from 1.2 V to 30 V and negative from -30 V to 0 V. Rejection is 69 dB at 120 Hz and at least 50 dB from 10 Hz to 2 MHz, output noise is 21 uVrms, and the BUF pin provides a buffered reference at up to 1 mA for the negative divider.

Order code and package

Order codeTPS7A3901DSCR
Positive input3.3 V to 33 V
Negative input-33 V to -3.3 V
Positive output1.2 V to 30 V
Negative output-30 V to 0 V
Output current per channel5 mA to 150 mA
Reference1.19 V, buffered at the BUF pin
Enablesingle positive logic input
Package10 pin WSON, 3 mm by 3 mm, DSC body
Pin count10
DocumentSBVS219, dual wide input regulator family, revision current at download

Electrical parameters that decide the application

Reference voltage1.172 V to 1.19 V to 1.208 V
Positive feedback voltage1.170 V to 1.188 V to 1.206 V
Negative feedback voltage-10 mV to 3.7 mV to 10 mV
Output accuracyplus or minus 1.5 percent over 1 mA to 150 mA
Rejection at 120 Hz69 dB
Rejection from 10 Hz to 2 MHz50 dB or better
Output noise, 10 Hz to 100 kHz21 uVrms
Positive UVLO rising1.4 V to 3.1 V
Negative UVLO falling-3.1 V to -1.4 V
UVLO hysteresis120 mV on the positive side, 70 mV on the negative side
BUF pin current0 to 1000 uA
Input and output capacitors10 uF nominal, 4.7 uF minimum
Thermal resistance44.4 C per W junction to ambient
Junction range-40 C to 125 C

Points to check before this part goes on a BOM

Two regulators in one body saves a package but not the thermal calculation. At 33 V in and 5 V out, 150 mA dissipates 4.2 W in a 3 mm body with 44.4 C per W, which is a 186 C rise and outside the part. The wide input is there for transients and for rails where the drop is small, and a board that runs 28 V across the regulator continuously has to move the heat upstream or use a switcher.

The negative channel is a genuine negative regulator, not an inverted positive one. It sources and sinks current, and its feedback divider is referenced to the buffered 1.2 V output at the BUF pin rather than to ground, which is what allows the negative output to be set without a level shift. The BUF pin can supply up to 1 mA, and the divider current has to be checked against that budget.

Single enable, two outputs, monotonic tracking. Both channels start from the same logic input and the datasheet specifies that the outputs track monotonically, which matters for a symmetric rail feeding an operational amplifier because a reversed startup can forward bias the input protection. The soft start ramp is set by the capacitor on NR/SS, and 10 nF to 1 uF covers the range the datasheet recommends.

The minimum load of 5 mA is a real requirement on the negative channel. A negative regulator that sinks current can be pushed above its setpoint by a load that returns current into the rail, and the datasheet's 5 mA floor is what keeps the loop in control. A board that only draws a few hundred microamps on the negative rail needs a bleed resistor, and that resistor then becomes part of the always on budget.

Rejection of 69 dB at 120 Hz is the number that matters when the input is a rectified mains rail with 100 Hz or 120 Hz ripple. A 1 V ripple becomes 350 uV, which is small enough for most analogue stages and not small enough for a 16 bit converter. Above 10 kHz the rejection holds at 50 dB or better to 2 MHz, so a switching preregulator at 300 kHz is attenuated by at least 50 dB rather than passing through.

Accuracy of plus or minus 1.5 percent is quoted from 1 mA to 150 mA, and the divider resistors add to it. The reference itself is specified from 1.172 V to 1.208 V, which is plus or minus 1.5 percent before any resistor tolerance, so a board that needs a symmetric rail within one percent has to trim or use better resistors. The positive and negative feedback voltages are specified separately, and the negative one is a small voltage around zero, which is why the specification is in millivolts rather than percent.

The 10 pin DSC body is 3 mm by 3 mm and carries both channels, so the two input capacitors and two output capacitors compete for the same few square millimetres. At 10 uF nominal with X5R derating, the effective capacitance at the pins is often below 5 uF, and the datasheet's own note on derating says the nominal value assumes that loss. Placing 4.7 uF of effective capacitance at each input and each output is the practical rule.

Where this order code fits

This order code suits analogue front ends that need a symmetric rail from an asymmetric bus, such as operational amplifier supplies in industrial automation, medical imaging and test equipment, plus the bipolar rails around data converters and bipolar sensors. The single positive logic enable and the monotonic tracking of the two outputs are what allow a symmetric rail to come up in a defined order. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Can both channels run from the same supply? No. The positive channel needs a rail above its output and the negative channel needs a rail below its output, so a symmetric analogue rail needs both a positive and a negative source.

Does the negative channel need a minimum load? Yes, 5 mA. Below that the loop cannot hold the setpoint and a bleed resistor has to carry the difference.

Is the enable 3.3 V compatible? Yes, it is a single positive logic input referenced to the positive input rail, so a 3.3 V signal enables both channels.

SUPERB supplies this order code in the DSC tape and reel with date codes, packing and country of origin on the offer, and the Component Lead Time Solutions page lists the fields to compare before a symmetric rail position is filled from another line.