Contact Us

TPS27081ADDCR

Brand: Texas Instruments
Texas Instruments TPS27081ADDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS27081ADDCR — Power Management & Signal Chain | Superb Automation

TPS27081ADDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS27081ADDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS27081ADDCR: high side load switch with adjustable slew rate, 1.2 V to 8 V

TPS27081ADDCR is a high side load switch that pairs a power PFET with a control NFET in one six pin body in a SOT-23-THIN body of 6 pins. The NFET level shifts a logic signal as low as 1 V up to the rail being switched, so a 1.8 V microcontroller can control an 8 V load without a level shifter. On resistance is 32 milliohm at a 4.5 V gate drive and the turn on ramp is set by two resistors and one capacitor, which is what keeps the inrush into a large load capacitance under control.

Order code and package

TPS27081ADDCRActive, SOT-23-THIN six pin, 3000 pieces on a large reel, SN finish, MSL-1
Temperature rangeminus 40 to 85 degrees on the addendum row, which is narrower than the 125 degree parts around it
Standby leakage100 nanoamp typical with the switch off
ESD2 kV human body model and 500 V charged device model on all pins
Body size2.9 mm by 2.8 mm by 0.75 mm

Electrical parameters that decide the application

Input range1.2 V to 8 V
Logic range1 V to 8 V on the ON/OFF pin
On resistance at 4.5 V32 milliohm
On resistance at 3 V44 milliohm
On resistance at 1.8 V82 milliohm
On resistance at 1.2 V155 milliohm
Absolute maximum on VIN and VOUT8 V referred to the R2 pin
Thermal resistance105 degrees per watt junction to ambient

Family variants and how they differ

R1pull up from the gate node to the rail, required in standby applications
R2 and C1set the turn on slew rate, R2 to ground when no ramp control is needed
Control NFETintegrated, removes the external level shifter on a 1.8 V or 1.2 V logic rail
PFET bodythe switch element, rated 8 V maximum
Pin orderthe R2 pin is the reference for the absolute maximum ratings, not ground

Points to check before this part goes on a BOM

The on resistance table is the whole selection story. 32 milliohm at 4.5 V sounds comfortable until the same part is used at 1.8 V logic, where it is 82 milliohm, and at 1.2 V where it is 155 milliohm. At 1 A that is 155 mV of drop and 155 mW of heat in a body with 105 degrees per watt of thermal resistance. The load current that is fine at 5 V is not fine at 1.2 V.

Slew rate control is not optional on a big capacitor. Switching a large output capacitance through a fast logic edge produces an inrush limited only by the capacitor ESR, which can trip the upstream supply or weld a connector contact. R2 and C1 slow the gate ramp so the inrush is defined by the ramp rather than by the capacitor. Without them the part still works, it just switches as fast as it can.

R2 to ground when no ramp control is wanted. The data sheet states this directly: in a standby power switch application where inrush is not a concern, R2 goes to ground and R1 alone holds the gate. Getting this wrong leaves the switch neither fully on nor off, which turns the PFET into a resistor and heats it.

100 nanoamp of leakage is the reason this part exists. A load switch that leaks a microamp defeats the purpose of switching the load off in a battery instrument. At 100 nanoamp the switch can isolate a whole subsystem and still leave the shelf life intact, which is a different job from a power switch in a mains powered product.

The 85 degree row is the constraint on industrial use. The addendum prints minus 40 to 85 for this body. Most of the converters and regulators on the same board are rated to 125. A board qualified at 85 degrees ambient without margin will have this part as the first item to fall out of specification.

The reference pin for the absolute maximum ratings is R2, not ground. That is unusual and it catches people. The 8 V limit on VIN and VOUT is referred to the R2 pin. If R2 is tied to a node that moves, the effective rating moves with it. R2 to ground keeps the ratings simple and is the connection to use unless slew control needs otherwise.

The integrated NFET is a level shifter, a driver and a protection in one. It means a 1.2 V microcontroller pin can switch a 5 V load directly, with no gate drive circuit and no series resistor. On a board that already has a 1.8 V logic rail this removes parts and removes the failure mode where a level shifter latch up takes the rail down.

Slow turn on has a second benefit beyond inrush. A ramp of a few hundred microseconds keeps the input rail from collapsing when the load connects, which matters when the upstream supply is a small battery or a long cable with significant resistance. The ramp is set by component values, so it can be tuned to the supply rather than fixed by the silicon.

This part is a switch, not a protection device. There is no current limit, no thermal shutdown and no fault output in this body. It turns a load on and off and it controls the ramp. A load that can short, or a connector a user can touch, needs a current limited switch or a fuse in front. Buying this part expecting protection is the usual mismatch between the data sheet and the application.

Pick the body for the copper, not for the pin count. The thermal resistance is 105 degrees per watt junction to ambient in a body this small, so one watt of loss in the switch lifts the junction by 105 degrees. At 1 A and 155 milliohm the switch dissipates 155 mW, which is comfortable, and at 2 A it dissipates 620 mW, which is not. The current that is acceptable depends on the gate drive actually available, and that is set by the logic rail, not by the load.

What to check on the bench before releasing this switch

Measure the on state drop at the real load current and the lowest expected gate drive, not at 4.5 V. That is the number that decides the heat and the rail sag.

Scope the output rise with the load capacitor fitted and the R2 and C1 values chosen. If the inrush still pulls the input rail down, the ramp is too fast for the supply, not for the switch.

Where this order code fits

It isolates a subsystem from a battery pack or a 5 V rail under 1.2 V or 1.8 V logic control, where the load capacitance is large and the inrush has to be tamed. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can a 1.2 V microcontroller drive the ON pin directly? Yes. The logic input is specified from 1 V, so a 1.2 V rail drives it without a level shifter. The on resistance at that gate drive is 155 milliohm, so the load current has to be small enough to accept that drop and the heat it produces.

Does it block current in both directions? No. It is a high side PFET switch with a body diode, so it blocks in the off state in one direction only. A load that can be back fed needs a second switch or a series diode.

What sets the turn on time? R1, R2 and C1 together. R1 holds the gate off, R2 and C1 slow the gate ramp. The data sheet gives the relationship, and the practical approach is to pick the inrush the supply can take and work back from that to the capacitor value.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.