Contact Us

TPS2553DBVR-1

Brand: Texas Instruments
Texas Instruments TPS2553DBVR-1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2553DBVR-1 — Power Management & Signal Chain | Superb Automation

TPS2553DBVR-1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2553DBVR-1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2553DBVR-1: precision adjustable current limited switch, 1.5 A, latch off, SOT-23-6

TPS2553DBVR-1 is a power distribution switch with an adjustable current limit from 75 mA to 1.7 A that latches off instead of folding back when the limit is reached in a SOT-23 body of 6 pins. The switch is intended for ports and slots where a fault has to be reported rather than absorbed. The current limit is set by one resistor, the response is fast enough to protect a connector, and the latch off behaviour means a shorted cable stays off until the system decides to retry.

Order code and package

TPS2553DBVR-1Active, SOT-23-6, 3000 pieces on a large reel, the latch off version
TPS2553DBVRthe constant current version of the same switch, which folds back instead of latching
TPS2553DBVT-1Active, 250 pieces on a small reel, the same latch off part
Package size2.9 mm by 1.6 mm, six pins, leaded body
ApprovalsUL listed, file E169910, and NEMKO to IEC 60950-1 amendment 1

Electrical parameters that decide the application

Input voltage2.5 V to 6.5 V
Continuous currentup to 1.5 A
Current limitadjustable from 75 mA to 1.7 A with a resistor from 15 k to 232 k
Limit accuracyplus or minus 6 per cent at 1.7 A
On resistance85 milliohm in the DBV body
Response time2 microsecond typical to a short circuit
Behaviour at the limitlatch off on this string, constant current on the non -1 version
Protectionsreverse input to output voltage protection, built in soft start, thermal shutdown

Family variants and how they differ

TPS2553-1latch off, the string on this page
TPS2553constant current, holds the current at the limit rather than switching off
FAULT pinopen drain, asserts low on an overcurrent or a reverse voltage condition
ILIM pinone resistor to ground sets the limit; the same resistor gives a lower limit when cold
BodySOT-23-6 at 2.9 mm by 1.6 mm with 15 kV ESD protection with an external capacitor

Points to check before this part goes on a BOM

Latch off and constant current are different products. The non -1 version holds the output at the current limit and lets the voltage collapse, which is what a USB port does when a device draws too much. This version switches off and stays off until the enable is cycled, which is what a docking slot does when a cable is shorted. Fitting the wrong one turns a recoverable fault into a dead port, or the other way round.

The limit resistor is not a precise current setting on its own. The accuracy is plus or minus 6 per cent at 1.7 A, and the same resistor produces a lower limit at cold temperature. A board that needs a guaranteed minimum current has to use the worst case column, not the 25 degree number, and a board that needs a guaranteed maximum has to do the same at the other end.

Reverse voltage protection is separate from reverse current protection. The part disables the switch when the output is driven above the input, which protects the devices on the input side. That is a comparator on the voltage, not a blocking FET, so a small reverse current flows before the switch turns off. For a battery rail that matters and for a USB port it does not.

A two microsecond response is what protects a connector. A shorted cable can pull tens of amps for the time it takes a fuse to open. The switch limits in microseconds, which is why it replaces a fuse in a port that has to survive a user plugging the wrong thing in. A fuse is still needed as a backup where the standard requires one.

The UL listing is part of the reason this part is specified. A product that has to meet a safety standard for a current limited output can cite the switch listing, which shortens the approval work. That is a purchasing and compliance advantage, and it disappears if a substitute without the listing is offered during a shortage.

The built in soft start limits the inrush into a capacitive load. A large bulk capacitor on a port would otherwise look like a short at the moment of connection. The controlled rise limits that current, but a very large capacitor can still hit the limit and the latch off version will then stay off, which looks like a dead port to a user who plugged in a device with a big capacitor.

The FAULT output is open drain and needs a pull up. Nothing drives it high. It asserts low on an overcurrent or a reverse voltage event, and the system has to read it before the latch is cycled, otherwise the fault is invisible and the retry looks random. On a port controller this pin is the difference between a diagnosis and a reset loop.

Eighty five milliohm at 1.5 A is 0.19 W in a SOT-23. That is a real temperature rise in a six pin body and the board copper is the heatsink. A port that is expected to deliver 1.5 A continuously needs a wide trace and a copper area, not just the switch.

The 15 kV ESD figure carries a condition. It is quoted with an external capacitor at the connector. Without that capacitor the port is only as good as the protection around it. A board that removes the capacitor to save cost loses the rating and the claim that goes with it.

What to confirm before this part goes on a purchase order

Confirm the version. The latch off and constant current parts share a body and a pinout and differ only in the -1 suffix, and the wrong one changes how a fault behaves on the product.

Ask for the date code and the reel label, and keep the UL listing reference on the offer. A substitute without the listing may work electrically and will not support the safety file.

For a port that has to meet a safety standard, the UL file number belongs on the offer next to the part number, because the listing is what the approval rests on and a substitute without it changes the compliance position of the whole product. That single reference is often the difference between an approval that takes weeks and one that has to be resubmitted.

Where this order code fits

It protects a USB port or a docking slot at up to 1.5 A, and latches off instead of folding back, so a shorted cable is reported rather than hidden. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it fold back or switch off at the current limit? This string switches off and latches. The version without the -1 suffix holds a constant current at the limit instead. That is the whole difference between the two parts.

How is the current limit set? By a resistor from the ILIM pin to ground, between 15 k and 232 k, covering 75 mA to 1.7 A. The limit also moves with temperature, so the resistor has to be chosen against the worst case column rather than the room temperature figure.

What happens if the output is driven above the input? The internal comparator detects the reverse voltage and disables the switch, and the FAULT output asserts. That protects the input side, and it is not the same as blocking reverse current instantly, since the switch takes a short time to turn off.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.