Contact Us

TPS22967DSGR

Brand: Texas Instruments
Texas Instruments TPS22967DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22967DSGR — Power Management & Signal Chain | Superb Automation

TPS22967DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22967DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22967DSGR single channel 4 A load switch with quick output discharge in the 2 mm by 2 mm WSON body

The TPS22967 is a single channel load switch built around an N channel MOSFET with a typical on resistance of 22 mOhm, in the eight pin DSG body that measures 2.00 mm by 2.00 mm with a thermal pad underneath. It carries up to 4 A continuously from any rail between 0.8 V and 5.5 V, and it needs a bias rail of 2.5 V to 5.5 V to drive the gate above the input.

The part is the switching element between a system rail and a load that the processor wants to be able to cut, sequence or restart without a second regulator. It adds a 225 Ohm pull down that discharges the output when the switch is off, a controlled rise time set by a capacitor on the CT pin, and a logic threshold low enough to be driven from a 1.2 V GPIO. There is no current limit on this part, so an overcurrent event is handled by the upstream supply and by the thermal pad under the die.

Key parameters taken from the TPS22967DSGR document

Rated continuous current4 A through one switch with the thermal pad soldered to copper
Input range0.8 V to VBIAS, so the switch passes a 0.9 V core rail as easily as a 5 V rail
Bias range2.5 V to 5.5 V on VBIAS, which is the rail that drives the gate
On resistance at 5 V bias22 mOhm typical and 33 mOhm maximum at 25 C, 35 mOhm maximum over minus 40 to 85 C
On resistance at 2.5 V bias26 mOhm typical and 38 mOhm maximum at 25 C, 40 mOhm maximum over temperature
Quiescent current at 5 V bias50 microamp typical and 75 microamp maximum with the switch on and no load
Quiescent current at 2.5 V bias20 microamp typical and 30 microamp maximum
Shutdown current2 microamp maximum on VBIAS and between 1 and 8 microamp on VIN depending on the input level
Logic thresholds1.2 V minimum for a high on the ON pin and 0.5 V maximum for a low, which covers 1.2 V, 1.8 V, 2.5 V and 3.3 V logic
Rise time1625 microsecond typical at 5 V in with a 10 Ohm load, 0.1 microfarad output and 1000 pF on CT
Turn on and delay1325 microsecond turn on and 500 microsecond delay at the same conditions, with the CT pin left open giving the fastest ramp
Output pull down225 Ohm typical and 300 Ohm maximum, active whenever the switch is off
PackageWSON DSG eight pins with exposed pad, 2.00 mm by 2.00 mm
Packing3000 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, marking ZTU
TemperatureMinus 40 to 85 C ambient as printed in the addendum and in the electrical tables

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

The bias rail is not optional and it is the item most often left out of a drawing review. The gate of the internal MOSFET has to sit above the input to keep the device in its low resistance region, so the part needs a supply that is at least as high as the highest rail it switches. A board that switches a 3.3 V rail and ties VBIAS to the same 3.3 V rail will work, but the resistance rows in the table are then the 2.5 V bias rows and not the 5 V ones: 26 mOhm typical against 22 mOhm, and 38 mOhm maximum against 33 mOhm. On a 3 A load that difference is 12 mW, small, but it is enough to move a junction temperature by a few degrees in a small body with a modest copper pad.

The output pull down is the reason many products choose this part over a plain P channel switch. When the switch is turned off the 225 Ohm resistor pulls the output to ground, so a load that is powered down cannot be held up by its own input capacitor and cannot leak back into the rail through a protection diode. That matters on a peripheral connector, where a user can plug a cable into a board that is off and back feed the rail through the cable. The resistor is only connected while the switch is off, so it costs nothing in the on state, but it does add 15 mA of load for the time the output capacitor takes to discharge.

The CT pin sets the ramp and the ramp sets the inrush. With 1000 pF the rise time at 5 V is 1625 microsecond typical, which into a 100 microfarad load is an average charging current of about 0.2 A, far below the 4 A the switch can pass. A board that leaves CT open gets the fastest ramp the part can produce, which is fine for a 1 microfarad load and hard on a rail that feeds several hundred microfarad of decoupling. The vendor application section gives the capacitor values for the usual ramp times, and it is worth following that table rather than choosing a capacitor by eye, because the pin is a current source into a capacitor and the ramp is linear rather than exponential.

There is no current limit inside this part, and the document says so in plain terms. A short on the output pulls whatever the upstream supply can deliver, and the only protection is the thermal pad and the thermal shutdown circuit that the family shares. A board that needs a defined fault current should use the current limited members of the same switch line instead of adding a fuse in series, because a fuse is slow, has a voltage drop at the rated current and is a field replaceable part that a production line has to count.

  • Inrush into the output capacitor with the CT capacitor the board actually fits, not with the pin left open.
  • Bias rail sequencing, because the switch must not be enabled before VBIAS is valid.
  • On resistance at the bias voltage the board uses, since the 5 V bias rows and the 2.5 V bias rows are different numbers.
  • Leakage of the load when the switch is off, with the pull down active and the output capacitor still charged.
  • Junction temperature at the real load current with the copper area the production board has.
  • Logic level of the driving GPIO during reset, because a floating ON pin can turn the load on.

Which projects this part fits

This part fits rail switching in notebooks and tablets, solid state drives, set top boxes and residential gateways, and telecom line cards where a 3.3 V or 5 V peripheral has to be cycled by firmware. It also fits battery powered instruments that need a sensor rail to be fully discharged between measurement cycles, because the pull down removes the residual charge that otherwise shows up as an offset. Where the board needs a defined fault current instead, the current limited parts of the same family are the ones to quote.

Questions that come up before a purchase order is released

Does the part work with the input above the bias rail?

It conducts, but the on resistance rises above the values in the tables. The document states that the device remains functional with VIN above VBIAS and that the resistance will be higher than published, so a board that switches a 5 V rail from a 3.3 V bias should confirm the resistance on the bench rather than assume the 22 mOhm row.

How is the rise time set?

By a capacitor from CT to ground. The pin sources a current into that capacitor, so the ramp is linear and the rise time scales with the capacitor. Leaving the pin open gives the shortest ramp, and the switching table lists the open pin case separately from the 1000 pF case.

Can the output be discharged faster?

The internal pull down is 225 Ohm typical, which is a time constant set by the output capacitor. A 100 microfarad output discharges with a 22.5 millisecond constant, so a full discharge takes about a hundred milliseconds. Faster discharge needs an external resistor or a switch with a stronger pull down.

Is a 1 microfarad input capacitor enough?

The recommended operating conditions list 1 microfarad as the minimum. On a board with a long trace from the regulator the ceramic should be close to the VIN pins, and a larger bulk capacitor at the regulator output is what supplies the first part of the inrush pulse.

What happens on a short circuit?

The current is limited only by the source. The part has no current limit, so the junction heats until the thermal circuit acts, and the upstream regulator may current limit first. A product that has to survive a permanent short on this port should use a current limited switch or add a fuse, and the choice belongs in the drawing review.

How SUPERB handles this line

We supply the TPS22967DSGR on original 3000 piece reels with the date code and the marking recorded on the packing list, and we can quote the 2.5 V bias members of the same line when a board switches a low rail only. The power management cross reference page lists the load switches we carry by current rating and body, pin to pin cross reference covers the case where a second source has to sit on the same land pattern, and kitting service is how we deliver a mixed set of switches against one build.