Contact Us

TPS22920YZPRB

Brand: Texas Instruments
Texas Instruments TPS22920YZPRB is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22920YZPRB — Power Management & Signal Chain | Superb Automation

TPS22920YZPRB

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22920YZPRB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22920YZPRB: 4 A load switch with 5.3 mOhm on resistance

TPS22920YZPRB is a single channel 4 A load switch with an integrated charge pump in a DSBGA body of 8 pins. It is an eight bump wafer level device with a 5.3 mOhm typical switch and a 0.75 V to 3.6 V input range.

Order code and package

Order codeTPS22920YZPRB, YZP package, eight bump DSBGA
Body1.90 mm by 0.90 mm, with and without backside coating in the family
Input range0.75 V to 3.6 V, aimed at the rails below a 5 V plane
Rated current4 A continuous
Output dischargeYes, about 1500 ohm pulldown while the switch is disabled

Electrical parameters that decide the application

On resistance5.3 mOhm typical at 3.6 V, rising towards 10 mOhm across the lower end of the input range
Current at 5.3 mOhm4 A drops 21 mV and dissipates 85 mW, which is the reason for the low resistance
EnableActive high, with a threshold specified between 0.9 V and the input rail
Output pulldown1250 ohm minimum, 1500 ohm typical at 3.3 V with a 3 mA test load
Charge pumpIntegrated, so the switch stays fully enhanced down to 0.75 V
Quiescent currentMicroamp range with the switch on, leakage only when it is off
Family variantThe L suffix marks the lower leakage member of the pair

Family variants and how they differ

TPS22920LSame 4 A switch with lower leakage for a battery rail that sleeps
TPS22914B2 A in a smaller four bump body with a higher on resistance
TPS229926 A with a separate bias pin so the gate drive does not depend on the input rail
TPS22992S6 A with overcurrent protection added to the thermal shutdown
TPS2051C0.5 A with a fixed limit and a fault flag, when the load needs protection rather than a switch

Points to check before this part goes on a BOM

The 5.3 mOhm typical at 3.6 V is what makes a 4 A switch usable in a body that is under two millimetres long. At 4 A the drop is 21 mV and the dissipation is 85 mW, so the load sees 3.58 V rather than a rail sagged by a tenth of a volt. The same current through a 40 mOhm switch would dissipate 640 mW, which no wafer level package can pass, so the resistance is not a refinement here, it is the product.

The resistance is not flat across the input range. It is specified at 3.6 V and rises as the input falls, reaching around 10 mOhm at the bottom of the range, because the charge pump has less headroom to hold the gate above the source. A rail at 1.2 V therefore drops about 40 mV at 4 A and dissipates 160 mW, double the figure at 3.6 V. That is still workable, but the thermal calculation has to use the resistance at the actual rail rather than the headline number.

The integrated charge pump is what makes the part work below 1.5 V. A plain N-channel switch needs a gate voltage above the input, and without a pump the switch would run in its linear region at low input and the on resistance would climb by an order of magnitude. The pump draws its current from the input, which appears in the quiescent figure, and it is the reason the part cannot be used as a pure passive device with the enable tied high and no supply.

The output pulldown at about 1500 ohm is a discharge path rather than a brake. A 100 uF load at 3.3 V discharges with a 150 ms time constant, so the rail is below a volt in about a third of a second. That is fast enough for a re enumeration but not fast enough to protect a load that must be at zero before the next event, and a product with that requirement needs an active discharge device rather than this switch.

The eight bump body has no leadframe and therefore no thermal tab. Heat leaves through the bumps into the copper, and the 85 mW at 4 A is small enough that the board copper is not critical, which is the point of the low resistance. A footprint with minimal copper still passes the current, and the part does not need the thermal vias that a higher resistance switch would.

The backside coating option matters for assembly, not for electrical behaviour. A coated body resists cracking under board flex, which is the failure mode of wafer level devices on thin boards, and the order code has to state which version is wanted. A reel of uncoated parts on a board that is expected to flex will pass test and fail in the field, and the failure looks like an open switch rather than a crack.

The active high enable threshold is specified between 0.9 V and the input rail, which means a 1.2 V GPIO can drive it but the margin at the bottom of the threshold window is thin. A 3.3 V or 5 V controller drives it with no concern, and a 1.8 V rail is comfortable. The pin must not be left floating, because the threshold window is wide enough that a floating pin can sit in the linear region and heat the switch.

The part switches, it does not protect. There is no current limit and no fault flag, so a short on the output pulls whatever the upstream supply can deliver until something else gives. A rail that needs a limit needs a switch with a limit and a flag, which in this family means the TPS22992S rather than this device, and the choice between them is about what has to happen when the load fails.

The current figure of 4 A is a switch rating and not a package rating. At 4 A and 5.3 mOhm the dissipation is 85 mW, which the eight bump body passes comfortably on a normal board, but at the bottom of the input range the resistance is nearer 10 mOhm and the dissipation doubles. The datasheet also notes that the coated version has a slightly different thermal path, since the coating is an added layer between the die and the air. For a rail that runs 4 A continuously the junction temperature should be measured on the actual board rather than calculated from the 3.6 V number.

Where this order code fits

It is the switch for a 3.3 V or lower rail that carries several amps, typically a processor core rail, a memory rail or a downstream module supply, where the drop across the switch has to stay under a few tens of millivolts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

What is the drop at 4 A? About 21 mV at the 5.3 mOhm typical at 3.6 V, and about 40 mV at 1.2 V where the resistance is nearer 10 mOhm.

Does it limit current? No, there is no current limit; the TPS22992S adds overcurrent protection to the same class of switch.

What is the difference from the L version? The L suffix is the lower leakage member, intended for a rail that stays off for long periods on a battery.

Can it switch a 5 V rail? No, the input range stops at 3.6 V; a 5 V rail needs the TPS22992 or the TPS22914 family.

What is the on resistance at 1.2 V? About 10 mOhm, roughly double the 3.6 V figure, because the charge pump has less headroom to hold the gate.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.