Contact Us

TPS2065CDBVR-2

Brand: Texas Instruments
Texas Instruments TPS2065CDBVR-2 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2065CDBVR-2 — Power Management & Signal Chain | Superb Automation

TPS2065CDBVR-2

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2065CDBVR-2 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2065CDBVR-2: 5 V, 1.5 A current-limited power distribution switch without output discharge

TPS2065CDBVR-2 is a fixed 1.5 A USB class power switch with a constant current limit, reverse current blocking and an output discharge path in a SOT-23 (DBV) body of 5 pins. It switches a 5 V rail to a port, limits the current to 1.5 A plus or minus 20 percent in constant current mode, and empties the output through an internal discharge when it is turned off.

Order code and package

Ordering stringTPS2065CDBVR-2, DBV package, 5-pin SOT-23, tape and reel
Family membersTPS2041C and TPS2051C (0.5 A), TPS2061C (1 A), TPS2065C and TPS2065C-2 (1.5 A), TPS2068C, TPS2069C and TPS2000C family (2 A)
Package5-pin SOT-23, 2.90 mm by 1.60 mm, and 8-pin MSOP PowerPAD and VSSOP options
Ambient range-40 C to 85 C
Output dischargeNot fitted on this -2 suffix part; the plain TPS2065C has the discharge resistor
ApprovalsUL listed and CB file E169910

Electrical parameters that decide the application

Input range4.5 V to 5.5 V on the IN pin
Rated current1.5 A continuous output
Current limitFixed 1.5 A with plus or minus 20 percent accuracy, constant current mode
Overcurrent response2 microsecond typical
Switch resistance96 milliohm typical, 130 milliohm maximum at 25 C in the SOT-23 body
Enable thresholds2 V high, 0.7 V low, with an active low option in the family
Reverse currentBlocked when the output is higher than the input
Fault outputOpen drain, deglitched, 5 mA sink capability

Points to check before this part goes on a BOM

The 4.5 V minimum input is the constraint that catches people out. This is a 5 V part, and a rail that sags to 4.3 V during a hot plug is outside the recommended range, so the switch resistance rises and the port voltage falls further. In a board fed from a 5 V adapter through a cable, the 4.5 V floor has to be checked at the connector under load, not at the adapter output.

At 1.5 A through 96 milliohm the switch dissipates 0.216 W, and the SOT-23 body has no thermal pad. That is the reason the 1.5 A rating comes with an ambient derating note in the data sheet, and the reason the MSOP PowerPAD version exists in the same family. A quad port board that puts four of these in a row on a 5 V rail has to add up four times 0.216 W and check the local air, or move to the power pad body.

The current limit is fixed and accurate to plus or minus 20 percent, so a 1.5 A part limits somewhere between 1.2 A and 1.8 A. That window is deliberate: a limit that is too accurate needs calibration, and a limit that is too loose does not protect the source. A downstream device that needs 1.4 A has to be checked against the 1.2 A minimum, not against 1.5 A, and this is where USB port budgets usually fail.

Constant current mode is not a latch. When the load exceeds the limit the output voltage falls and the current stays near the limit until the load is removed, which is what a charging port needs because a tablet can draw more than a port limit and still charge slowly. A host that expects the port to shut down on overload will see the voltage collapse instead of the fault flag, and the flag only comes from the FLT pin after the internal deglitch.

Reverse current blocking matters in a multi port product where one port is powered and another is not. Without it, a device plugged into the unpowered port would back feed the 5 V rail through the switch body diode, and the symptom is a port that works until another port is loaded. The blocking behaviour is internal, so there is no external diode to add and no extra drop in the path.

This part has no output discharge, and that is the reason to order the -2 suffix rather than the plain C part. When the switch turns off the output capacitor keeps its charge, which is what a port that feeds a backup capacitor or a supercapacitor needs. On a USB port the same behaviour means the next plug event presents a charged node, so a host that needs a clean re-enumeration takes the plain TPS2065C with the internal discharge instead. The two parts share the body, the pinout and the limit.

The forward drop of the switch is part of the port budget. At 1.5 A and 96 milliohm the drop is 144 mV, and with the 130 milliohm maximum it is 195 mV, so a 5.0 V input leaves 4.80 V to 4.86 V at the connector before the cable is counted. A USB specification that asks for 4.75 V at the device under 1.5 A therefore needs an input above 4.9 V, and the 4.5 V minimum input of this part is the floor below which the resistance rises and the drop grows faster than the current.

Where this order code fits

It is used for USB ports and hubs, notebooks, desktop boards, digital televisions and set top boxes, and anywhere a 5 V branch has to survive a shorted cable without taking down the main supply. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference between the C and the -2 suffix? The C parts have an output discharge path across the switch, the -2 parts do not. Electrical ratings and current limits are the same.

Does the current limit latch off? No. It holds a constant current until the overload is removed, and the fault pin reports the condition. A latch off behaviour is not available in this family.

Can two ports share one switch? Not with independent protection. One switch means one limit, so a fault on either port pulls both down and the fault flag does not say which one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.