TMP1075DR
Product Specifications
TMP1075DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP1075DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP1075DR twelve bit digital temperature sensor in the industry standard LM75 footprint
The TMP1075DR is a digital temperature sensor in a SOIC-8 body that matches the pinout and the register map of the long established LM75 and TMP75 parts. It measures from minus 55 to plus 125 C with twelve bit resolution, which is a quarter of a degree per code, and it reports plus or minus a quarter of a degree typical with a maximum of one degree from minus 40 to plus 110 C. The point of the part is that a board built around the older device can be improved without a board change and without a firmware change, because the interface and the register addresses are the same.
The supply range is 1.7 to 5.5 V and the current is the reason many products move to this part: ten microamps typical at the default conversion rate, 2.7 microamps at the slowest rate, and 0.37 microamps in shutdown. The device offers thirty two addresses through three strap pins, an open drain alert output with a programmable limit and a fault queue, an SMBus reset that recovers a bus stuck low, and compatibility with the mixed fast mode of an I3C bus. The vendor states that every unit is tested on a production setup traceable to NIST and calibrated to ISO 17025 accredited standards.
Key parameters taken from the TMP1075DR document
| Range | minus 55 to plus 125 C, twelve bit resolution, 0.0625 C per code |
| Accuracy | plus or minus 0.25 C typical, plus or minus 1 C maximum from minus 40 to plus 110 C, plus or minus 2 C maximum over the full range |
| Supply | 1.7 to 5.5 V, temperature reading independent of the supply, 0.03 C per volt of supply rejection |
| Interface | two wire SMBus and I2C, thirty two addresses, SMBus reset, alert output, compatible with I3C mixed fast mode |
| Conversion | 27.5 ms default, also 55, 110 and 220 ms, one shot conversion in 4.5 to 7 ms |
| Current | 10 microamps typical at the default rate, 2.7 microamps at the slowest rate, 52 microamps during a conversion, 0.37 microamps in shutdown |
| Alert | open drain, programmable limit and fault queue, 0.4 V maximum low level at 3 mA |
| Compatibility | LM75 and TMP75 pinout and register map, same footprint in the SOIC body |
| Repeatability | 0.0625 C, long term drift 0.0625 C after 500 hours at 150 C |
| Package | SOIC, body D, eight pins, also VSSOP and WSON bodies |
| Order code facts | TMP1075DR, SOIC D 8 pins, 2500 pieces on a large reel, NIPDAU, minus 55 to plus 125 C, marking 1075, Active |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The conversion rate and the current are one decision. At the default 27.5 ms rate the device converts about thirty six times a second and draws ten microamps, and at the slowest 220 ms rate it draws 2.7 microamps. The difference matters in a battery product and it does not matter at all in a mains powered one. What does matter in both is that a rate faster than the thermal time constant of the board buys nothing: the die follows the copper with a lag of seconds, so converting thirty times a second measures the same temperature thirty times.
The alert output is a small state machine and it needs to be configured with intent. The limit register, the hysteresis and the fault queue decide when the pin asserts and when it releases. A queue of one fault means a single noisy conversion can trip the alert, and a queue of four means the pin waits for four consecutive out of limit conversions. For a fan control that is the difference between a quiet product and one that cycles, and for a protection input it is the difference between nuisance trips and a late response.
Thirty two addresses on three pins is more than most boards need and it is what allows a memory module or a line card to carry eight or sixteen sensors on one bus without a multiplexer. The strap pins can be tied to ground, the supply, SDA or SCL, and the combinations that use SCL and SDA depend on the bus state during the address phase, which is the same trap as on any strap addressed part. Addresses that use only ground and the supply are stable through any reset sequence and are the safer choice when more than four devices share the bus.
The LM75 compatibility claim is worth testing rather than assuming. The register map and the pinout match, and the resolution is finer than the older device, so a firmware that reads the temperature register as a nine bit value will see the extra bits in the lower positions and may interpret them as a large positive number. The fix is a shift or a mask, and it belongs in the porting checklist rather than in a field update. The device identification register also differs, so any code that probes for the old part by its identifier needs a new branch.
- Reading against a calibrated probe at three temperatures, after the resolution and the sign handling are verified in firmware.
- Alert threshold and hysteresis exercised by heating the board, with the fault queue setting the product will use.
- Supply current at the conversion rate the product actually uses, and in shutdown if the product sleeps.
- Bus behaviour after a stuck low condition, to confirm the SMBus reset recovers without a power cycle.
- Address strap reading at power up on every device on the bus, since a duplicate address shows as a bus fault.
- Placement relative to the heat source, because the die follows the copper and a sensor in the wrong corner measures the board, not the processor.
Which projects this part fits
This sensor is used on server and storage boards, in telecom line cards and central office equipment, in notebook and handheld products, in battery management, in printers and connected peripherals, in thermostats and HVAC controls, and in any board that has to report a temperature over an existing I2C bus. The LM75 footprint makes it the drop in choice for a product that was released years ago around the older part and now needs better accuracy and lower current without a board change.
Questions that come up before a purchase order is released
Is this really pin compatible with the LM75?
The document states the same form factor and pinout and the same register map, and the supply range covers the older part. The differences are in resolution, in the device identification register and in the number of addresses. A board can be upgraded without a board change, and the firmware needs a check on how it reads the temperature register, because the extra bits change the value if they are not masked.
What accuracy can a product claim?
Plus or minus one degree maximum from minus 40 to plus 110 C and plus or minus two degrees maximum over the full range, with a quarter degree typical. A claim tighter than that needs a calibration step per unit, and a claim over the full range has to use the two degree number rather than the typical.
Why does the current change with the conversion rate?
Because the device spends most of its time idle between conversions, and the idle current is a small fraction of the conversion current. At the slowest rate the average current falls to 2.7 microamps. A product that needs both a fast response and low average current can use one shot conversions triggered by the host, which draws 52 microamps only during the 4.5 to 7 ms conversion.
Does the alert pin need a pull up?
Yes, it is an open drain output and it can only sink current. The pull up value has to suit the input it drives and the bus voltage, and the low level is guaranteed at 3 mA. The same pin also carries the fault queue output, so the receiving circuit should debounce according to the queue setting rather than the raw pin.
What is the difference between the D, DGK and DSG bodies?
Package size and, in one case, accuracy. The D body is the SOIC, the DGK is the VSSOP and the DSG is a 2 by 2 mm WSON. The document prints the same accuracy for the D and DGK bodies, a slightly narrower window for the DSG body, and the number of addresses and the conversion rate settings differ on the smallest SOT body. The body letter in the order code decides which column applies.
How SUPERB handles this line
We supply the TMP1075DR on the original 2500 piece reel with date code and lot traceability, and we confirm the body letter and the moisture class before the parts reach a line. For a product moving from an LM75 to this part we quote it against the existing footprint so the substitution can be checked before any board change. The power management cross reference and medical device components pages cover the parts that share this bus, and the how to verify a drop in replacement page describes the checks we run before recommending a substitution.