Contact Us

SN65MLVD207DR

Brand: Texas Instruments
Texas Instruments SN65MLVD207DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65MLVD207DR — Power Management & Signal Chain | Superb Automation

SN65MLVD207DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65MLVD207DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65MLVD207DR: 200 Mbps multipoint LVDS transceiver with a type 2 receiver and a 100 mV offset

SN65MLVD207DR is a multipoint LVDS transceiver in the eight pin SOIC body that drives a 480 mV to 650 mV differential signal into a 50 ohm load, receives with the 100 mV offset of a type 2 input, and runs from a single 3.3 V rail in a SOIC body of 8 pins. The SN65MLVD207 combines one M-LVDS driver and one type 2 receiver in an eight pin SOIC. The driver swings 480 mV to 650 mV into a 50 ohm load with a common mode between 0.8 V and 1.2 V, and the receiver applies a 100 mV offset so an undriven or shorted bus produces a defined output. The pin out follows the SN75ALS180 footprint, and the signalling rate runs to 200 Mbps on a controlled bus.

Order code and package

Order codeSN65MLVD207DR
Functionmultipoint LVDS driver and receiver pair
Signalling rateup to 200 Mbps
Supply voltage3.3 V nominal
Driver differential output480 mV to 650 mV into 50 ohm
Receiver typetype 2, 100 mV offset
Packageeight pin SOIC, D body
Pin outSN75ALS180 footprint
DocumentSLLS558C, December 2002, revised January 2007
Family variantsSN65MLVD201 and SN65MLVD203, SN65MLVD206

Electrical parameters that decide the application

Differential output magnitude480 mV minimum, 650 mV maximum
Change in differential output between statesminus 50 mV to plus 50 mV
Steady state common mode output0.8 V to 1.2 V
Change in common mode between statesminus 50 mV to plus 50 mV
Peak to peak common mode output150 mV maximum
Maximum steady state open circuit output0 V to 2.4 V
Supply current, driver only13 mA typical, 22 mA maximum
Supply current, receiver only4 mA typical, 13 mA maximum
Supply current, both enabled16 mA typical, 24 mA maximum
Supply current, both disabled1 mA typical, 4 mA maximum
Package power rating at 25 C725 mW in the eight pin SOIC
Derating above 25 C5.8 mW per C
Power rating at 85 C377 mW
Receiver offset100 mV, type 2

Points to check before this part goes on a BOM

The type 2 receiver is the reason to pick this part over its siblings. A 100 mV offset means the input has to see a real differential before the output changes state, so an open pair, a shorted pair or an undriven bus settles the receiver into a known level instead of oscillating on noise. On a backplane where cards are hot plugged and the driver may be disabled, that behaviour decides whether the receiving logic sees a burst of edges or a quiet line. The type 1 variants in the same family, the SN65MLVD201 and SN65MLVD203, are centred instead and rely on external biasing for the same guarantee.

Footprint compatibility within the family is a package statement, not a function statement. The SN65MLVD207 follows the SN75ALS180 pin out, while the SN65MLVD206 follows the SN75176, so a board that swaps between them keeps its copper and changes its receiver behaviour and its driver enable polarity. The ordering table lists the footprint for each part for exactly this reason, and a swap made on the strength of the package alone is the kind that passes a quick test and fails in the field.

Supply current of 16 mA to 24 mA with both blocks enabled is the dominant term on a small bus. At 3.3 V that is 53 mW to 79 mW per node, so sixteen nodes cost about 0.85 W of quiescent power before any signal current. The driver itself delivers only 13 mA into 50 ohm at the maximum differential voltage, which is 8.5 mW, so the termination network and the quiescent current set the budget and the signal current is a rounding error.

The 200 Mbps figure comes with conditions that a backplane can break. It is measured with a 100 MHz clock and a 200 Mbps pseudorandom pattern with 0.5 ns edges into a controlled load, so it describes the silicon and not the bus. A long stub, a connector pair or a card edge with more than a few centimetres of uncontrolled trace will close the eye long before 200 Mbps, and the usual approach is to simulate the actual bus or to start at 100 Mbps and measure.

The package dissipation ratings in the eight pin SOIC are 725 mW at 25 C, derating 5.8 mW per C, which leaves 377 mW at 85 C. Against 79 mW of quiescent power that looks generous, and it is until a fault arrives: a driver held into a short or a bus that is driven by two cards at once puts the full output stage into a resistive load, and the derating figure is what decides how long that state can last. Current limiting is not part of the driver specification, so the fault has to be cleared by the controller.

The common mode output sits between 0.8 V and 1.2 V with a 150 mV peak to peak swing during switching. That 0.4 V window is narrow enough that the receiver threshold has to be stable with respect to it, which is why the offset is specified as a differential quantity. A bus with poor ground return between cards shifts the common mode at the receiver, and the margin against the 100 mV offset is what remains after that shift.

Enable and disable behaviour matters at the system level. With both blocks disabled the supply current falls to 1 mA to 4 mA, so a card can be quieted without removing its rail, and the driver enters a high impedance state that leaves the bus to another talker. The receiver state during that time is defined by the type 2 offset, which is the property that makes the 207 the safer choice on a bus where the active driver changes.

Where this order code fits

This order code belongs on multipoint backplanes, clock and trigger distribution in instrumentation and telecom shelves, motor control racks and any chassis that carries a shared differential bus between more than two boards. It is chosen over a point to point LVDS part when the same pair has to reach eight or sixteen cards, and over RS-485 when the data rate has moved past what a slow transceiver can carry. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference between the type 1 and type 2 receivers in this family? A type 1 receiver switches around zero differential volts, and a type 2 receiver has a 100 mV offset built in. The offset gives a defined output when the bus is idle, open or shorted, which is what a multipoint backplane needs when the driving card is removed or disabled. The type 1 parts, the SN65MLVD201 and SN65MLVD203, need external fail-safe biasing to reach the same behaviour.

Can this part run at 5 V? The driver output levels and the recommended operating conditions in this document are written around a 3.3 V supply. A 5 V backplane needs a different family, and the logic side of this part is 3.3 V, so a 5 V controller needs level shifting on the enable and data pins. Mixing a 5 V bus with a 3.3 V transceiver is the kind of change that appears to work on a short bench cable and fails on a real backplane.

How many nodes can share one pair? The standard allows a multipoint bus of up to 32 nodes, and the practical limit is set by the loading and the stub lengths rather than by the transceiver. Each node adds capacitance and leakage, so a bus that reaches 200 Mbps with four cards will not reach it with sixteen. The 480 mV minimum differential output is specified into a 50 ohm load, which assumes the two end terminators are fitted and the intermediate cards present a small load.

What happens when the driving card is removed? The type 2 receiver holds its last defined state rather than chattering, because the 100 mV offset keeps the output from following noise on an undriven pair. That is the behaviour a backplane needs for a hot swap. The transmitter side goes high impedance when both blocks are disabled, which is why the enable pins should be tied to the card's presence signal rather than left floating.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.