SN65LVDS3487DR
Product Specifications
SN65LVDS3487DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LVDS3487DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LVDS3487DR: the quad driver with the MC3487 footprint
The SN65LVDS3487DR is the member of the LVDS31 group that keeps the MC3487 pin arrangement. It carries four current mode differential drivers, each able to deliver 247 mV minimum into a 100 ohm load with 350 mV typical, at rates up to 400 Mbps and with roughly 1.7 ns of propagation delay. The output stage is arranged so that a disabled driver, or a driver whose supply has collapsed to 0 V, presents a high impedance to the pair.
The difference between this part and the SN65LVDS31 is the pinout and the enable arrangement rather than the electrical core. That matters in a refresh project: a board that was laid out for an MC3487 can usually be reworked to this part without moving traces, and the swing drops from 5 V differential levels to LVDS levels, which removes most of the radiated energy from the cable.
Key data for the SN65LVDS3487DR
| Function | Four differential drivers, pin compatible with the MC3487 arrangement |
| Rate | 400 Mbps per driver with 500 ps typical rise and fall times |
| Levels | 350 mV typical and 247 mV minimum into a 100 ohm load |
| Delays | 1.7 ns typical propagation delay |
| Power | 3.3 V single rail, about 25 mW per driver at 200 MHz |
| Protection | Bus terminal ESD beyond 8 kV, high impedance when disabled or unpowered |
Body, marking and reel data
| Body | SOIC D, 16 pins, 9.90 mm by 3.91 mm, with a TSSOP option in the same group |
| Reel | 2500 pieces on a 330 mm reel in the packing table, while the orderable column for the plain row prints no quantity |
| Marking | LVDS3487 on the rows that print a marking, against LVDS31 on the shared die rows |
| Handling | Moisture level 1, 260 C peak, unlimited floor life |
| Temperature | Minus 40 C to 85 C |
What an MC3487 replacement actually changes
The electrical change is the swing. A 5 V differential driver switches several volts across the pair, and the edge couples into every nearby trace. An LVDS driver switches about 350 mV around a 1.2 V common mode, and the same cable radiates far less. In an enclosure that already passes emissions with the older part, the new one leaves margin; in an enclosure that fails, it is often the cheapest fix on the list.
The second change is the receiver at the far end. A 5 V driver can be read by a 5 V receiver with a simple divider, but an LVDS driver needs an LVDS receiver to see the 350 mV swing properly. A retrofit has to change both ends, and that is the point where the bill of materials grows rather than shrinks.
Ordering details worth checking first
The published orderable table for this string is inconsistent, and that is worth knowing before a purchase order goes out. The plain row prints a body and no quantity, the .B row prints a TSSOP body with 90 pieces in a tube, and the packing table prints a 2500 piece reel on a 330 mm carrier for the same order string. A buyer who reads only the first table can order a tube quantity by accident, so the reel size should be named explicitly on the order and confirmed on the acknowledgement.
The second point is the marking. Some rows of the shared die print LVDS31 and some print LVDS3487, and a receiving inspection that expects one string will reject the other. The third is the enable logic: the four drivers are grouped in pairs on this pinout, so a board that needs independent control of all four has to use the other member of the family.
The quantity question on this string
This is one of the strings where the published tables disagree with each other, and that is worth stating plainly to a buyer. The orderable column prints a body with no quantity on the plain row, the .B row prints a tube of 90 in a TSSOP body, and the packing table prints a 2500 piece reel on a 330 mm carrier for the same string. A purchase order that copies the part number without a packing note can therefore come back with a tube.
We handle this by naming the body, the reel size and the carrier width on the quotation, and by asking the vendor to confirm the same three fields on the acknowledgement. Where a line needs the TSSOP body rather than the SOIC, we say so before the order is placed rather than after the goods arrive, because a footprint change on a running board costs more than the parts.
Where the part replaces a 5 V device, the comparison work is set out on the pin to pin cross reference page. Where the incoming goods need a documented check against the reel label, the method is on our incoming inspection plan page.