Contact Us

INA826AIDGK

Brand: Texas Instruments
Texas Instruments INA826AIDGK is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA826AIDGK — Power Management & Signal Chain | Superb Automation

INA826AIDGK

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA826AIDGK from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA826AIDGK: the tube carrier, and the row the addendum marks for a last buy

INA826AIDGK is the cost effective precision instrumentation amplifier in the 8 pin VSSOP, supplied as an 80 piece bulk tube, and the orderable addendum marks this row under the time buy column with a last production note while the 2500 piece reel of the same body stays active.

That status is the whole reason a buyer looks at this page. The part itself is the family's: 150 microvolts maximum of input stage offset, 104 dB of rejection at a gain of 10, 200 microamps and a 3 volt supply floor. A tube of 80 suits a bench and a repair depot, and a line that still runs this carrier should be moving to INA826AIDGKR rather than counting on the tube row.

INA826AIDGK as the vendor document publishes it

Input stage offset40 microvolts typical, 150 microvolts maximum
Output stage offset200 microvolts typical, 700 microvolts maximum
Total offset at a gain of 1060 microvolts typical, 220 microvolts maximum
Gain equation1 plus 49.4 kilo-ohms divided by the gain resistor
Gain range1 to 1000 V/V
Gain drift at 11 ppm per degree typical, 2 ppm maximum
Gain drift above 135 ppm per degree maximum
Common mode rejection at a gain of 10104 dB minimum
Common mode rejection at 5 kHz100 dB minimum at a gain of 10
Power supply rejection at a gain of 1100 dB minimum, 130 dB typical at a gain of 10
Voltage noise18 nanovolts per root hertz at a gain of 100 and above
Bandwidth at a gain of 11 MHz
Bandwidth at a gain of 10060 kHz
Input common mode rangefrom the negative supply to 1 volt below the positive supply
Input protection40 volts beyond the supply rails, input current limited to 8 milliamps
Supply current200 microamps
Supply range3 to 36 volts single, plus or minus 1.5 to plus or minus 18 volts dual
Outputrail to rail
Temperature rangeminus 40 to plus 125 degrees
Vendor statustime buy on the package addendum, last production, 80 piece bulk
Catalogue codeINA826AIDGK
Vendor stringINA826AIDGK, tube; INA826AIDGKR is the active reel
BodyVSSOP, DGK, 8 pin, 3.00 by 3.00 millimetres
Lead finishNIPDAU
Moisture levellevel 2, 260 degrees, one year floor life

A cost position that keeps the precision rows

INA826AIDGK is the low cost member of the precision family: 40 microvolts typical and 150 microvolts maximum of input stage offset, 200 microvolts typical and 700 maximum of output stage offset, and a gain drift of 1 ppm per degree at unity and 35 above unity. The current draw is 200 microamps and the supply range starts at 3 volts.

What separates it from a general purpose amplifier is the rejection: 104 dB minimum at a gain of 10 and 100 dB minimum at 5 kHz, which is the row that decides an industrial channel on a shared ground. What separates it from the more expensive members of the family is the offset, three times the 35 microvolts of the low noise parts, and the bandwidth, 1 MHz at unity rather than 2 or 4.7. For a bridge at a gain of 100 the offset is the first row and the bandwidth is irrelevant.

An input range that includes the negative supply

The input common mode range of INA826AIDGK includes the negative supply and reaches to within 1 volt of the positive one, and the output is rail to rail. That combination is what lets the part run from a single 3 volt rail with a ground referenced sensor and still use the whole converter range.

Most instrumentation amplifiers lose the bottom of their input range, which is exactly where a ground referenced bridge sits. A part that includes the negative rail can be connected directly to a load cell whose bridge sits at ground, with no charge pump and no negative supply, and the rail to rail output then swings to within millivolts of the rail into the converter. The 1 volt gap at the top is the remaining limit: a sensor whose common mode is above that needs a different front end, not a bigger supply.

Rejection that holds to five kilohertz

The common mode rejection of INA826AIDGK is 104 dB minimum at a gain of 10 and 100 dB minimum at 5 kHz at the same gain, which is a rejection specification given at a frequency rather than only at DC. The power supply rejection is 100 dB minimum at unity gain, and the inputs are protected to 40 volts beyond the rails with the input current limited to 8 milliamps.

The 5 kHz figure is the honest one for a channel that sits near a motor drive or a switching supply. A part whose rejection is only quoted at DC usually falls by 20 dB or more by a few kilohertz, and the common mode at the switching frequency then appears as an error. Here the attenuation is specified where the noise is, and a 10 volt switching common mode at 5 kHz becomes 300 microvolts at the input rather than millivolts.

Two hundred microamps and a three volt floor

INA826AIDGK draws 200 microamps and runs from a single supply of 3 to 36 volts, or a dual supply of plus or minus 1.5 to plus or minus 18 volts. That floor is the lowest in the precision family and it is what makes the part usable on a 3.3 volt rail with a 10 per cent tolerance, where a 4.5 volt part would need a boost.

The gain is 1 plus 49.4 kilo-ohms divided by the resistor between the gain pins, covering 1 to 1000. The current draw and the supply floor together set the application: a battery instrument that measures a bridge once a second can run this part from the same 3.3 volt rail as the converter and the radio, and a 36 volt ceiling lets the same part sit on a 24 volt industrial rail with the usual derating.

Eighteen nanovolts, and where the noise stops mattering

The voltage noise of INA826AIDGK is 18 nanovolts per root hertz at a gain of 100 or above, which is close to the thermal noise of a 20 kilo-ohm resistor. On a 350 ohm bridge the source dominates at about 2.4 nanovolts, so the amplifier sets the noise floor; on a 10 kilo-ohm source the two are comparable, and above 100 kilo-ohms the source decides everything.

That is the useful way to read a noise row. An 18 nanovolt amplifier is quiet enough for a strain gauge and not quiet enough for a low impedance magnetic sensor, where single digit nanovolts are wanted. It is also the row that pairs with the bandwidth: 1 MHz at unity gain and 18 nanovolts give a noise of about 18 microvolts across the full band, which is small next to the 150 microvolt offset and large next to a 10 microvolt signal.

Where a cost effective precision amplifier belongs

INA826AIDGK belongs on a bridge or load cell channel in an industrial module, a 4 to 20 milliamp transmitter with a 3.3 volt rail, a battery test channel, an analogue input card where the common mode sits at ground, and any board that needs 100 dB of rejection at a switching frequency without paying for the low noise family.

It stops where the offset has to be under 35 microvolts, where the bandwidth has to be above 1 MHz, where the supply is under 3 volts, and where the common mode is at the top of the rail, because the input range stops a volt short of the positive supply. Our amplifier cross reference page covers the three family members side by side, and the traceability report page covers the certificate that travels with the reel.

A last buy row is a stock decision. Our obsolete part cross reference hub covers the active reel beside it, and the obsolescence management page covers the wider question of a carrier that is being retired.

Is the die disappearing? The addendum marks the tube row for a last buy while the reel of the same body is active, so the part continues and the carrier does not.

What changes on the reel? Quantity and moisture handling only; the electrical rows are the same.