Contact Us

SN65HVD75DRBR

Brand: Texas Instruments
Texas Instruments SN65HVD75DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD75DRBR — Power Management & Signal Chain | Superb Automation

SN65HVD75DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD75DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD75DRBR: 3.3 V RS-485 transceiver at 20 Mbps for short, terminated buses

SN65HVD75DRBR is the fast member of a three part family, a half duplex differential driver and receiver on 3.3 V with the same IEC level protection as the slow one and a driver edge rate built for a backplane in a SON body of 8 pins. It runs at 20 Mbps, keeps the 80 mV receiver hysteresis and the more than plus or minus 15 kV human body model, plus or minus 12 kV IEC contact discharge and plus or minus 4 kV fast transient burst ratings of the family, draws under 1 mA quiescent and under 2 uA in standby, allows more than 200 nodes, and is specified from minus 40 to plus 125 degrees. At 20 Mbps the cable has to be short and terminated at both ends, which is the condition the datasheet prints against the rate.

Order code and package

SN65HVD75DRBRSON DRB body, 8 pins, printed in the addendum as Active with 2500 pieces on a large reel on the A row, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 125 degrees, marking HVD75
SN65HVD75DRBTthe same body on a 250 piece small reel, the row for a build that needs hundreds rather than thousands
SN65HVD75DRthe SOIC D body, 2500 on a large reel, for a board that keeps the wider outline
SN65HVD72 and SN65HVD78the 250 kbps and 50 Mbps members, same pinout, same protection. The 72 is the one for a long field bus, the 78 for a cabinet backplane
Package column notethe DRBR rows in this document are printed against a VSSOP DGK column while the suffix is the SON DRB body, so the body has to be named on the purchase order rather than read from the package cell alone

Electrical parameters that decide the application

Supplya single 3.3 V rail with 5 V tolerant logic inputs, so the port works behind either controller family without a shifter
Signalling rate20 Mbps, which on a properly terminated pair supports a few metres of backplane trace and a short cable, not a field run
Node countmore than 200 nodes at this rate, which is the family property and applies as long as the bus stays short enough for 20 Mbps
Hysteresis80 mV, the same receiver as the slow member, which is why a 20 Mbps link still tolerates a noisy cabinet environment
ESDmore than plus or minus 15 kV human body model, more than plus or minus 12 kV IEC 61000-4-2 contact and more than plus or minus 4 kV IEC 61000-4-4 burst on the bus pins
Quiescent currentunder 1 mA operating and under 2 uA in standby, so a fast port does not cost more idle power than a slow one
Driver outputspecified into 54 ohm, the standard test load, and the differential output stays inside the RS-485 window across the full temperature range
Edge ratethe driver transitions are fast enough for 20 Mbps without slope control, which is the opposite of the fault protected family where a resistor sets the slew
Fail safedefined receiver output on an open, shorted or idle bus, so a controller does not clock a false start bit
Power sequencingglitch free on power up and power down, which matters on a hot plugged backplane card
PackageSON 3 mm by 3 mm, with the pads under the body and no visible joint after reflow
Temperatureminus 40 to plus 125 degrees on every printed row, so a cabinet at 70 degrees ambient has 55 degrees of junction headroom

Family variants and how they differ

75 against 72the 72 is 250 kbps and works on a 1200 m cable, the 75 is 20 Mbps and does not. A board that changes from one to the other has to re check the cable, the termination and the connector
75 against 78the 78 is 50 Mbps and needs an even shorter bus. At 20 Mbps the 75 already sits at the point where stub length and termination tolerance decide whether the link works
Against a full duplex partthe SN65HVD73 family is the four wire version at the same rates for a point to point link that needs simultaneous traffic. The 75 is the two wire part
Against an isolated transceiveran ISO1450 handles the same 50 Mbps class with a barrier in the package, at several times the price and with an isolated supply requirement
Against a 5 V partthe 3.3 V rail removes one supply and one level shifter, and the differential output at 3.3 V still meets the RS-485 minimum into 54 ohm

Points to check before this part goes on a BOM

The rate and the cable length are one decision, not two. At 20 Mbps the driver edge is fast enough that a 100 m run with a stub hanging off the middle of the pair will show ringing at the receiver, and the part will be blamed for a link that fails on long drops. The datasheet signalling rate row is written against a terminated, short bus, and a customer who needs 20 Mbps over 300 m is asking for a physical layer that does not exist.

The package column in this document's addendum is worth reading twice. The DRBR rows are printed against a VSSOP DGK cell while the suffix is the SON body, which is a column artefact rather than a real second package. A purchase order that copies the package from that cell will arrive with a different outline quoted against it, so the string and the body drawing should be the reference.

The 2500 piece reel on this row is one third less than the 3000 on the 250 kbps member, and that difference is easy to miss when a bill of materials is cloned from one part to the other. It changes the reorder point and the line side stock, not the function, but production planning is where such differences cost money.

The standby current under 2 uA is the same as the slow member, which is unusual for a fast part and is a consequence of the receiver being the same circuit. The dominant state current follows the bus load, and a 20 Mbps bus with 120 ohm termination draws about 55 mA from the driver at 3.3 V, which is the number a small regulator has to carry.

The 80 mV hysteresis that helps at 250 kbps is less useful at 20 Mbps, because at that rate the receiver is working on edges that are already fast. What matters at 20 Mbps is the common mode window and the symmetry of the differential output, and both are specified on the same rows for the whole family.

The part carries no fault protection beyond the ESD ratings. A 24 V miswire on a bus pin is outside the common mode window and outside the absolute maximum, and the failure mode is a shorted pin rather than a graceful trip. Cabinets where a bus wire can touch a supply need the 1794 family or an external clamp.

Reading the family as a ladder

The three members share one die, one pinout and one protection network, and differ in the driver edge rate and the receiver bandwidth. That is why a board can be qualified once and then offered at three rates, and why a customer who has a working 250 kbps product can move to 20 Mbps with a part number change if the cable and termination already support it.

The ladder also sets the price order: the slow member is the cheapest, the 20 Mbps member is the volume part, and the 50 Mbps member costs more for the same silicon because of test and binning. A quote that lists the 78 where the 72 was asked for is a quote with a higher price and no benefit on a 250 kbps bus.

What the order code decides

The string reads SN65HVD75 for the device, DRB for the SON body and R for the large reel, with T in the same position for the 250 piece small reel and a plain DR for the SOIC. The A and B rows in the addendum are packing revisions of the same body, and the G4 rows are the lead free declaration, so none of them changes the electrical part.

Where this order code fits

Factory automation backplanes, motion control links and telecom rack internal buses are the applications the vendor prints, and a short terminated pair carrying 20 Mbps between two cards in the same cabinet is the case this member is bought for. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What data rate does SN65HVD75DRBR support? 20 Mbps. The family also offers 250 kbps as the SN65HVD72 and 50 Mbps as the SN65HVD78 on the same pinout.

How long can the cable be at 20 Mbps? Short and terminated at both ends. The datasheet rate is specified on a terminated test bus, and a 100 m run with stubs is outside what the driver edge supports at 20 Mbps.

Is the reel 2500 or 3000 pieces? 2500 on the printed rows of this string, on a large reel. The 250 kbps member of the same family is printed at 3000, so a cloned bill of materials carries a different reorder quantity.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.