SN65HVD21DR
Product Specifications
SN65HVD21DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD21DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD21DR: a 5 V RS-485 transceiver that reaches 20 V below ground
The SN65HVD21DR belongs to the SN65HVD2x family of extended common mode RS-485 transceivers. The common mode window runs from minus 20 V to plus 25 V, which is more than double what TIA/EIA-485 asks for, and it is the reason this family shows up in motor drives, inverters and factory floors where the ground potential between two cabinets is not the same.
The 21 member carries up to 256 nodes at moderate rates, up to 5 Mbps, with a slew limited driver that shapes the edges to keep high frequency emissions down. The receiver includes a failsafe circuit that forces a high output within 250 microseconds of losing the signal, so an unplugged cable or a bus with no active driver reads as idle rather than as noise.
Key data for the SN65HVD21DR
| Common mode | Minus 20 V to plus 25 V, against the minus 7 V to plus 12 V the standard requires |
| Rate and nodes | Up to 5 Mbps with slew limited outputs, up to 256 nodes on one bus, 50 m at 25 Mbps in the family table |
| Protection | Bus pin protection above 16 kV HBM, thermal shutdown, positive and negative current limiting |
| Failsafe | Receiver output high within 250 microseconds after loss of input, covering open, shorted and idle bus conditions |
| Current | 7 mA typical and 11 mA maximum with the driver enabled and the receiver disabled, 1 uA maximum standby |
| Receiver | More than 100 mV of hysteresis, differential output of at least 1.8 V into a 54 ohm load |
Body, marking and reel data
| Body | D, SOIC 8 at 4.90 mm by 3.91 mm, with a P DIP 8 for through hole builds |
| Reel | 2500 pieces on a large reel on the .A and G4 rows, carrier tape 12.4 mm, 330 mm reel |
| Marking | VP21 on the SOIC body and 65HVD21 on the DIP body, so the printed code names the package |
| Handling | Moisture level printed as Call TI on the .A row and level 1 with unlimited floor life on the G4 row |
| Temperature | Minus 40 C to 85 C on every row of the family |
Why the extended common mode window matters
RS-485 is a differential standard, and the theory says the ground difference between nodes cancels. In a cabinet with a 15 kW inverter, the ground difference does not cancel: it moves by tens of volts during a switching event. A transceiver that stops at the standard window will either misread or latch up. The SN65HVD2x family was built for that environment, and the minus 20 V to plus 25 V window is the specification that gets it onto drive and inverter boards. The receiver keeps its thresholds across that whole window, which is what makes the claim usable rather than decorative.
The slew limited driver is the second half of the story. Faster edges mean more radiated noise, and a motor cable is an excellent antenna. Shaping the edges costs data rate, which is why the 21 stops at 5 Mbps and the family publishes a 500 kbps member for long cable runs. Matching the rate to the cable is cheaper than adding shielding to a cabinet. A ground wire run alongside the pair helps, but it does not replace a transceiver that can swing through the offset.
Questions we get when this code is on a BOM
The usual question is which member of the family to use, because the five parts share a pinout and differ in rate, drive strength and equalisation. The 20 carries 25 Mbps to 64 nodes, the 21 carries 5 Mbps to 256 nodes, the 22 carries 500 kbps over up to 1200 m, and the 23 and 24 add receiver equalisation for long cable. The part number on the BOM should be checked against the cable length and the node count, not only against the last build.
The second question is about the addendum rows. The plain SN65HVD21DR row prints no reel quantity and Call TI for moisture, while the .A and G4 rows print 2500 pieces. A buyer who needs a firm reel count should order a row that publishes one, and we state which row we are quoting rather than leaving the suffix to the warehouse.
How SUPERB supports this line item
We stock and source the SN65HVD21DR alongside the rest of the SN65HVD2x family, and we send the row, the marking and the reel quantity with every offer. Customers who are changing a bus from a standard transceiver to an extended common mode part can use the how to verify a drop in replacement checklist, which starts with the common mode window and the failsafe behaviour.
For drive and inverter builds the interface section is usually quoted with the isolation and the protection parts on the same order, which the one stop BOM sourcing route covers.